Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature as much as 30°
One year limited service warranty through manufacturer start at date of
    purchase

SUCHES AS:
Fan with wire and adapter, shroud and two zip ties

NEEDS:
Connecting to motor can and connecteding into receiver

SPECS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more wonderful item to compliment the above discussed item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Port
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, eliminate prior to exposing ESC to moisture

The below item likewise sets really well with the item being discussed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Advised for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) prepared to run (not for usage in heavier
    cars such as E-Revos or E-Maxx class cars)
USB programs capability through Castle Link USB adapter (not included,
    order CSEM6300)
Waterproof for usage in nearly every environment (not meant for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces many stock brushed motors
Four magnet, four pole rotor for higher torque
1.4" size slotted stator
Detachable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Change, Guidelines, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery adapter of modeler's choice

SPECS:
ESC;
Input Voltage: 2S LiPo minimum, THREE LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery adapter
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have actually bought this item along with the item that you are currently checking out.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Right here is one more item that compliments the item being discussed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of two which are utilized on the E-Maxx dual motor
    set-up.