Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year limited warranty through producer beginning at date of
    purchase

INCLUDES:
Fan with wire and adapter, shroud and 2 zip ties

REQUIRES:
Attaching to motor can and connecteding into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more fantastic item to compliment the above mentioned item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases utilized on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

INCLUDES:
Fan with Wire Lead and Connector
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, remove prior to exposing ESC to moisture

The listed below item likewise pairs actually well with the item being talked about.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) ready to run (not for use in much heavier
    automobiles such as E-Revos or E-Maxx class automobiles)
USB programming capability by means of Castle Link USB adapter (not suched as,
    order CSEM6300)
Waterproof for use in almost every environment (not intended for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes numerous stock brushed motors
4 magnet, four pole rotor for higher torque
1.4" size slotted stator
Detachable end bell

INCLUDES:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Connector,
    On/Off Switch, Guidelines, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery adapter of modeler's choice

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, 3S LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery adapter
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Connector: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have purchased this item together with the item that you are currently reviewing.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

Right here is one more item that praises the item being talked about.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

INCLUDES:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is only one of 2 which are utilized on the E-Maxx double motor
    set-up.