Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year limited warranty through producer start at date of
    purchase

CONSISTS OF:
Fan with wire and port, shroud and two zip ties

NEEDS:
Connecting to motor can and plugging into receiver

SPECS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more wonderful thing to match the above pointed out thing?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older design cases used on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

CONSISTS OF:
Fan with Wire Lead and Connector
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, remove prior to exposing ESC to moisture

The listed below thing also sets really well with the thing being discussed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Recommended for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for use in heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB programs ability via Castle Link USB adapter (not suched as,
    order CSEM6300)
Waterproof for use in almost every environment (not meant for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes many stock brushed motors
Four magnet, 4 pole rotor for greater torque
1.4" size slotted stator
Easily removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Connector,
    On/Off Change, Instructions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery port of modeler's option

SPECS:
ESC;
Input Voltage: TWO LiPo minimum, 3S LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery port
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Connector: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have actually gotten this thing together with the thing that you are presently reading about.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

Here is one more thing that compliments the thing being discussed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is just one of two which are used on the E-Maxx dual motor
    set-up.