APC 7x5 Thin Electric Prop

This is a 7x5E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered airplane just (not for glow engines).

FEATURES:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with two adjuster rings that adapt to various motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
2 composite adapter rings
One instruction sheet

REQUIRES:
ALL props require balancing, this is CRUCIAL, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 5
Hub inner size: 0.25"

You will like this item if you have the item earlier discussed.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Accuracy Composites.
For use on electric powered airplane just (not for glow engines).

FEATURES:
Gray composite construction
Features two adjuster rings that adapt to various motor shafts

INCLUDES:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props require balancing, this is CRUCIAL, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 6
Hub inner size: 0.25" (6.3mm)

Right here is another item that compliments the item being discussed.



This is a 6x5.5E Thin Composite Propeller from Advanced Accuracy Composites.
For use on Electric powered airplane just (not for glow engines).

FEATURES:
Gray composite construction

INCLUDES:
One 6x5.5E Thin Electric Propeller

REQUIRES:
ALL props require balancing, this is CRUCIAL, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 6"
Pitch: 5.5
Hub inner size: 0.25"

The listed below item also sets really well with the item being discussed.



These are the ElectriFly Prop Saver O-rings from Terrific Planes.

FEATURES:
Twists around the prop to hold it on and protect it throughout crashes

INCLUDES:
5 prop saver O-rings

REQUIRES:
Setup

Many others have actually acquired this item along with the item that you are currently checking out.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Adapter Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing material:
1 x 9g TITAN Servo Sets (with devices)

Want another wonderful item to match the above pointed out item?

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction lowers turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring instruction sheet

REQUIRES:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Glow engines