Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combo Helicopter Kit. This amazing package includes not only the T-REX 700E DFC Kit, however also aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This kit also includes an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, three DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This incredibly combo provides you with an amazing helicopter kit and a similarly remarkable electronics and High Voltage package all in the same box.

700E DFC Features:

The Align 700E DFC helicopter is geared up with the low CG DFC rotor head to efficiently reduce wind resistance throughout flight and supply the most direct and exact control feel back to the pilot, supplying exciting 3D performance and inconceivable flight speed.
CCPM direct servo linkage design gets rid of the weight of a double push-pull linkage system, for quick response and exact control.
Integrated servo mounts on the primary shaft bearing obstructs enable the cyclic servos to be mounted directly to the bearing obstructs, and when combined with the composite product frame plates, develops a clean and uncluttered appearance.
The frame uses an integrated composite carbon product strategy for ease of upkeep and high rigidity, while the increased front opening location enables simple battery setup.
The ingenious moving battery tray rails are imbedded into the 3K side frames, with a patented spring loaded locking system enabling quick battery access along with battery security.
A leading mounted motor base brings the motor's center of mass better to the rotating disc, enhancing 3D agility and allowing blade drafts to efficiently cool the motor.
The motor mount system features a 3rd bearing block to supply better motor shaft support, lowering torque shift and reducing the danger of striping an equipment.
The drive train features a high spec MOD1 112T CNC helical primary equipment and a helical cut MOD1 tail drive equipment to improve the equipment mesh and decrease equipment sound throughout flight.
A leading mounted ESC platform utilizes the primary blade air flow for efficient ESC cooling.
The lightweight H-shaped electric gadget retention system provides security, along with an ergonomically right design to streamline operation.
The consisted of Align 750MX brushless motor features a ribbed case and fan to drastically increase cooling and improve total power output.
The transmission features a structured design and permits simple disassembly.
The high quality tail gearbox design, combined with a dual point mounted tail pitch control assembly assists to decrease slop and boost rudder control.
The high torque ranked one method bearing base, bearing supported dual push point rudder control design, high speed ranked tail blade grip thrust bearings and a 3rd bearing primary shaft support were consisted of to hold up against the abuse of extreme 3D flight.
A pre-painted high grade fiberglass canopy utilizes 4 point anti-vibration installing system to enable uncomplicated canopy setup. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Diameter: 1562mm

Tail Rotor Diameter: 281mm

Motor Drive Gear: 12T

Main Drive Gear: 112T

Autorotation Tail Own Gear: 104T

Tail Own Gear: 22T

Own Gear Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Includes:

(1) T-REX 700E DFC Kit
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Needed to Total:

7-channel or more helicopter radio system
(2) 6S Li-Po 4500 ~ 5200mAh
(1) 2S Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge