Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combination Helicopter Set. This extraordinary package includes not only the T-REX 700E DFC Set, however likewise aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This set likewise includes an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, 3 DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This extremely combination offers you with an extraordinary helicopter set and an equally impressive electronics and High Voltage package all in the very same box.

700E DFC Features:

The Align 700E DFC helicopter is geared up with the low CG DFC rotor visit successfully lower wind resistance throughout flight and offer the most direct and exact control feel back to the pilot, offering thrilling 3D performance and inconceivable flight speed.
CCPM direct servo linkage style gets rid of the weight of a double push-pull linkage system, for fast reaction and exact control.
Integrated servo installs on the primary shaft bearing blocks enable the cyclic servos to be installed directly to the bearing blocks, and when combined with the composite material frame plates, produces a clean and uncluttered look.
The frame makes use of an integrated composite carbon material technique for ease of maintenance and high rigidness, while the increased front opening location allows for basic battery setup.
The ingenious moving battery tray rails are anchored into the 3K side frames, with a trademarked spring filled latching mechanism enabling quick battery gain access to along with battery defense.
A top installed motor base brings the motor's center of mass closer to the rotating disc, enhancing 3D dexterity and allowing blade drafts to successfully cool the motor.
The motor install system includes a third bearing block to offer better motor shaft assistance, lowering torque shift and decreasing the threat of striping an equipment.
The drive train includes a high spec MOD1 112T CNC helical primary gear and a helical cut MOD1 tail drive gear to improve the gear mesh and decrease gear sound throughout flight.
A top installed ESC platform utilizes the primary blade air flow for effective ESC cooling.
The lightweight H-shaped electric device retention system offers defense, along with an ergonomically correct style to streamline operation.
The consisted of Align 750MX brushless motor includes a ribbed case and fan to dramatically increase cooling and improve overall power output.
The transmission includes a structured style and permits basic disassembly.
The high quality tail transmission style, combined with a dual point installed tail pitch control assembly assists to decrease slop and boost rudder control.
The high torque rated one way bearing base, bearing supported dual push point rudder control style, high speed rated tail blade grip thrust bearings and a third bearing primary shaft assistance were consisted of to withstand the abuse of severe 3D flight.
A pre-painted high grade fiberglass canopy utilizes 4 point anti-vibration mounting mechanism to enable effortless canopy setup. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Diameter: 1562mm

Tail Rotor Diameter: 281mm

Motor Drive Gear: 12T

Main Drive Gear: 112T

Autorotation Tail Own Gear: 104T

Tail Own Gear: 22T

Own Gear Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Consists of:

(1) T-REX 700E DFC Set
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Needed to Total:

7-channel or more helicopter radio system
(2) SIX Li-Po 4500 ~ 5200mAh
(1) TWO Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge