Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combination Helicopter Kit. This unbelievable plan consists of not only the T-REX 700E DFC Kit, however likewise aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This set likewise consists of an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, three DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This very combination provides you with an amazing helicopter set and an equally impressive electronic devices and High Voltage plan all in the same box.

700E DFC Functions:

The Align 700E DFC helicopter is equipped with the low CG DFC rotor go to effectively reduce wind resistance during flight and offer the most direct and accurate control feel back to the pilot, offering thrilling 3D efficiency and inconceivable flight speed.
CCPM direct servo linkage style eliminates the weight of a double push-pull linkage system, for fast reaction and accurate control.
Integrated servo installs on the primary shaft bearing obstructs allow the cyclic servos to be mounted directly to the bearing obstructs, and when combined with the composite product frame plates, develops a clean and uncluttered look.
The frame uses an integrated composite carbon product strategy for ease of upkeep and high rigidness, while the increased front opening location allows for simple battery setup.
The innovative sliding battery tray rails are inserted into the 3K side frames, with a patented spring packed latching mechanism allowing for fast battery gain access to along with battery defense.
A top mounted motor base brings the motor's center of mass closer to the turning disc, improving 3D agility and permitting blade drafts to effectively cool the motor.
The motor install system includes a 3rd bearing block to offer better motor shaft support, decreasing torque shift and lessening the danger of striping an equipment.
The drive train includes a high specification MOD1 112T CNC helical primary gear and a helical cut MOD1 tail drive gear to improve the gear mesh and decrease gear noise during flight.
A top mounted ESC platform uses the primary blade air flow for effective ESC cooling.
The lightweight H-shaped electrical gadget retention system provides defense, along with an ergonomically appropriate style to simplify operation.
The consisted of Align 750MX brushless motor includes a ribbed case and fan to drastically increase cooling and improve total power output.
The transmission includes a structured style and enables simple disassembly.
The high quality tail gearbox style, combined with a dual point mounted tail pitch control assembly assists to decrease slop and boost rudder control.
The high torque ranked one way bearing base, bearing supported double push point rudder control style, high speed ranked tail blade grip thrust bearings and a 3rd bearing primary shaft support were consisted of to withstand the abuse of extreme 3D flight.
A pre-painted high grade fiberglass canopy uses 4 point anti-vibration mounting mechanism to allow effortless canopy setup. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Size: 1562mm

Tail Rotor Size: 281mm

Motor Drive Equipment: 12T

Main Drive Equipment: 112T

Autorotation Tail Drive Equipment: 104T

Tail Drive Equipment: 22T

Drive Equipment Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Includes:

(1) T-REX 700E DFC Kit
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Needed to Complete:

7-channel or more helicopter radio system
(2) SIX Li-Po 4500 ~ 5200mAh
(1) TWO Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge