Align T-REX 700E DFC Flybarless HV Super Combo Kit w/Motor, ESC, 4 HV

This is the Align T-REX 700E DFC Flybarless HV Super Combo Helicopter Kit. This incredible bundle consists of not just the T-REX 700E DFC Kit, however also aluminum and carbon fiber tail booms, a 690 3G carbon fiber blade set and a 105mm 3K carbon fiber tail blade set. This set also consists of an Align 530kV, 750MX brushless motor, a Castle Creations ICE2 HV 120 brushless ESC, 3 DS700 High Voltage Brushless digital cyclic servos and one DS750H High Voltage Brushless digital rudder servo. This extremely combo supplies you with an incredible helicopter set and an equally remarkable electronics and High Voltage bundle all in the exact same box.

700E DFC Functions:

The Align 700E DFC helicopter is geared up with the low CG DFC rotor go to efficiently lower wind resistance throughout flight and supply the most direct and exact control feel back to the pilot, offering thrilling 3D efficiency and inconceivable flight speed.
CCPM direct servo linkage style removes the weight of a double push-pull linkage system, for fast response and exact control.
Integrated servo mounts on the primary shaft bearing blocks enable the cyclic servos to be installed straight to the bearing blocks, when combined with the composite material frame plates, creates a clean and uncluttered appearance.
The frame uses an integrated composite carbon material technique for ease of upkeep and high rigidness, while the increased front opening area allows for basic battery setup.
The innovative sliding battery tray rails are inserted into the 3K side frames, with a patented spring filled locking system enabling fast battery access in addition to battery protection.
A top installed motor base brings the motor's center of mass better to the turning disc, enhancing 3D agility and permitting blade drafts to efficiently cool the motor.
The motor mount system includes a third bearing block to supply better motor shaft assistance, lowering torque shift and minimizing the risk of striping a gear.
The drive train includes a high spec MOD1 112T CNC helical primary gear and a helical cut MOD1 tail drive gear to improve the gear mesh and reduce gear sound throughout flight.
A top installed ESC platform uses the primary blade air flow for effective ESC cooling.
The lightweight H-shaped electric gadget retention system supplies protection, in addition to an ergonomically correct style to streamline operation.
The consisted of Align 750MX brushless motor includes a ribbed case and fan to considerably increase cooling and improve overall power output.
The transmission includes a structured style and enables basic disassembly.
The high quality tail transmission style, combined with a double point installed tail pitch control assembly helps to reduce slop and increase rudder control.
The high torque ranked one method bearing base, bearing supported dual push point rudder control style, high speed ranked tail blade grip thrust bearings and a third bearing primary shaft assistance were consisted of to endure the abuse of extreme 3D flight.
A pre-painted high grade fiberglass canopy uses 4 point anti-vibration mounting system to enable uncomplicated canopy setup. 

700E DFC Specifications:

Length: 1345mm

Height: 360mm

Width: 208mm

Main Blade Length: 690mm

Main Rotor Diameter: 1562mm

Tail Rotor Diameter: 281mm

Motor Drive Gear: 12T

Main Drive Gear: 112T

Autorotation Tail Drive Gear: 104T

Tail Drive Gear: 22T

Drive Gear Ratio: 1:9.33:4.37

Weight (With Motor): 2900g

Includes:

(1) T-REX 700E DFC Kit
(1) Aluminum Tail Boom
(1) 3K Carbon Fiber Tail Boom
(1) 690 3G Carbon Fiber Blade Set
(1) 750MX Brushless Motor (530KV)
(3) DS700H High Voltage Brushless Servo
(1) DS750H High Voltage Brushless Servo


(1) Castle ICE2 HV 120 Brushless ESC
(1) 105mm 3K Carbon Fiber Tail Blade Set

Needed to Complete:

7-channel or more helicopter radio system
(2) 6S Li-Po 4500 ~ 5200mAh
(1) 2S Li-Po 1900 ~ 2300mAh
Dial Pitch Gauge or Digital Pitch Gauge