Align T-Rex 600EFL Pro Super Combo

This is the Align T-Rex 600 EFL Pro Super Combo. Align has actually taken their T-Rex 600 EFL Pro helicopter and combined it with a 600MX brushless motor, one 600 3G Carbon fiber blade set, 3 DS610 digital servos, a Castle ICE HV 80 Brushless ESC, one DS650 digital tail servo and their cutting-edge 3GX Programmable Flybarless System.

3GX Programmable Flybarless System Features:

• Align's recently revamped 3GX represents a brand name brand-new generation of multi function flybarless system.
• The 3GX is presently the lightest and tiniest flybarless system presently available on the marketplace. Its 2 ports are able to straight link Spektrum and JR satellite receivers, along with complete support of Futaba's S-BUS system.
• Based on Align's 3G FL760 manual setup procedure, the 3GX can be quickly setup in just a couple of minutes through a simple procedure. Plus, the 3GX supports all of the CCPM swashplate systems presently available on the marketplace- including 90, 120, 135, and 140 degree swashplates.
• The included computer system setup software application directs the user through a step by step setup procedure, enabling fast setups without leaving out any steps.
• With the anticipated soon to be launched Bluetooth connection set, the 3GX can be configured wirelessly from your PC.
• Custom parameters have been opened up in the 3GX, allowing pilots to fine tune a variety of settings for the rudder and swashplate. The settings export function lets you share your custom-made settings with your friends.
• Align's 3GX features brand name brand-new gyroscope sensing units, allowing it to be used under severe conditions. Its dual axis plus rudder sensor significantly enhances rudder and swashplate correction precision, especially when compared to last generation 3G.
• The 3GX is suitable for helicopter classes from 250 to 800, glow engine and electric powered. Its exceptional vibration resistant characteristic appear, even when installed with more difficult double sided installing tape.
• The 3GX uses a 16 bit processor, making it 4 times faster than previous generation, along with an entirely re-written firmware. The result is a remarkable stability improvement from previous generation, with stability that rivals a flybarred helicopter, yet possesses explosive agility.
• With integrated in pirouette settlement function, Align's 3GX has the ability to stabilize your helicopter on a set point during pirouetting maneuvers. Pirouetting turns kind of maneuvers are quickly achieved with precision.
• The 3GX's rudder will give you a consistent rudder feel, even when under high speed conditions. This excellent control feel will enable pilots of all skill levels to experience the best integration between 3GX and helicopter.
• With the APS gyro, your helicopter will have the capability to self stabilize, hold position as well as altitude, and even self-governing way point flights as well as return home.

T-Rex 600EFL Pro Features:

• Tail pitch system equipped with high precision bearing
• High speed thrust bearings in tail blade grips
• New lightened landing gear assembly with lower center of mass
• High quality painted fiberglass canopy with 4-point fast release installs
• Newly created aerodynamically efficient low drag flybarless head assembly, with removable blade grip pitch arm for simple upkeep
• Ingenious moving battery tray rails imbedded into the 3K side frames, with trademarked spring loaded locking system, allows for fast battery access as well as battery protection.
• Its frame uses 2mm carbon fiber plates of the greatest spec. It's made of a trademarked composite product and a building technique that skillfully uses frame area that enhances general rigidness
• Leading installed motor base brings the motor's center of mass better to rotating disc, improving its 3D dexterity
• Brand brand-new 600 class 12S high voltage brushless motor offers generous torque and power output, yet takes in lower typical current to lengthen battery life
• Optimum motor pinion ratio and tail gear ratio accomplishes the most efficient power output and flight characteristics
• Heatsink embedded into motor mount for efficient cooling of motor
• Motor mount consists of third bearing block to offer motor shaft support; efficiently minimizing torque induced shifts, and lessens gear striping issue
• Makes use of direct link CCPM swashplate control system that allow direct and fast control action.
• Specially created anodized CNC servo horns are not just aesthetically pleasing, but are exceptionally rigid.
• Utilizes the greatest spec CNC modue-1 helical primary gear, with greatest load tolerance and lowest sound
• Ergonomically created H-shaped electronic mount to offer flexible organization or devices, and decrease wire clutter
• Brand brand-new CNC machined metal tail transmission, with thicker side plates to increase rigidness
• High quality 5mm carbon rod and CNC metal tail scissor control arms are used in rudder control system to improve rudder locking and control effectiveness
• Extra radial bearing is contributed to the one way bearing block to ensure smooth rotation

Consists of:
One T-REX 600EFL PRO Kits Set
One Aluminum Tail Boom
One 600 3G Carbon fiber blades
One 600MX Brushless Motor (510KV)
Three DS610 Digital servo
One DS650 Digital servo
One 3GX Flybarless System
One Castle ICE HV 80 Brushless ESC
One 6A External BEC w/ 5.1V Two-way Step-down voltage regulator

Requires:
Dial Pitch Gauge
Receiver (7-channel or more)
Transmitter (7-channel or more, helicopter system)
SIX Li-Po 2600 ~ 4600mAh X2 (3300mAh suggestion)

Requirements:

3GX Programmable Flybarless System
Running Temperature: -10~60 degree
X and Y axis Operating Angle Variety: -300~+300 degree
Z axis Operating Angle Variety: -600~+600 degree
Size: 36.5x25.2x15.6mm
Weight: 11g
Maximum working voltage: 8.5V

T-Rex 600EFL Pro
Length: 1160mm
Height: 353mm
Width: 210mm
Main Blade Length: 600mm
Main Rotor Diameter: 1347mm
Tail Rotor Diameter: 260mm
Motor Drive Equipment: 13T
Main Drive Equipment: 112T
Autorotation Tail Drive Equipment: 131T
Tail Drive Equipment: 34T
Drive Equipment Ratio: 1:8.61:3.85
Weight (with Motor): 2290g