Align T-Rex 600E DFC 3GX Electric Helicopter Super Combo

This is the Align T-Rex 600E DFC 3GX Super Combo.

T-Rex 600E Pro DFC Features:

The frame utilizes 2mm carbon fiber plates of the highest specification. Patented composite material building technique cleverly use frame space that enhanced overall rigidness, as well as developed a minimalistic beauty.
Heatsink embedded into motor install for efficient cooling of motor.
Utilize direct link CCPM swashplate control system to allow direct and fast control action. Specially developed anodized CNC servo horns are not just visually pleasing, but are extremely rigid.
The most optimal motor pinion ratio and tail gear ratio to achieve the most effective power output and flight characteristic.
Additional radial bearing is added to the one way bearing block to make sure smooth rotation, and get rid of jammed one way bearing.
Motor install consists of 3rd bearing block to offer motor shaft assistance, successfully reduce torque caused shifts, and lessen gear striping issue.
Brand brand-new CNC machined metal tail transmission, with thicker side plates to increase rigidness. The more streamlined design also permits easier disassembly.
Tail pitch mechanism geared up with high precision bearing.
New lightened landing gear assembly with lower center of gravity.
Equipped with the low CG DFC rotor head, successfully reduce wind resistance throughout flight, providing the most direct and precise control feel back to the pilot, and exhibits exciting 3D performance and unthinkable flight speed.
Innovative moving battery tray rails imbedded into the 3K side frames, with patented spring packed latching mechanism, allowing for quick battery access along with battery protection.
Top installed motor base bringing the motor???s center of mass closer to rotating disc, enhancing 3D agility.
Utilizes highest spec CNC modue-1 helical primary gear, with highest load tolerance and most affordable noise.
High quality 5mm carbon rod and CNC metal tail scissor control arms are used in rudder control system to improve rudder lockingand control effectiveness.
Brand brand-new 600 class 12S high voltage brushless motor providing generous torque and power output, yet takes in lower average current to lengthen the life of batteries.
High quality brand-new tail gearbox design, integrated with brand-new dual point installed tail pitch control assembly to lessen slops and increase rudder control precision.
Total pitch variety of +15~-15 degrees, for the supreme 3D explosive power.
High speed thrust bearings in tail blade grips.
High quality painted fiberglass canopy with 4-point quick release mounts.

3GX Programmable Flybarless System Features:

3GX is presently the smallest and lightest flybarless system available on the marketplace. 2 ports to directly link Spektrum and JR satellite receivers, in addition to complete assistance of Futaba's S-BUS system
Illustrated directions on the computer system setup software assists direct the user through an action by step setup procedure, allowing for quick setups without leaving out any steps
With 3GX's built in Align RCE-G600 governor function, no external governor is needed to reduce electronic wire clutters
3GX utilizes brand brand-new gyroscope sensors of the highest specifications when compared with other flybarless systems presently on the marketplace, permitting it to be used under severe conditions. Dual axis plus rudder sensor dramatically enhances swashplate and rudder correction precision compared with last generation 3G. This is clearly visible in stable hover along with highly aerobatic regimens
The exceptional vibration resistant attribute is evident even when installed with harder double sided installing tape
3GX utilizes 16 bit processor which is 4 times faster than previous generation, in addition to an entirely re-written firmware. The result is a dramatic stability enhancement from previous generation, with stability that measures up to a flybarred helicopter, yet posses explosive agility
3GX's rudder enables consistent rudder feel even under high speed conditions. This exceptional control feel will permit pilot of all ability levels to experience the perfect combination in between 3GX and helicopter.
Brand brand-new upgraded 3GX represents a brand-new generation of multi function flybarless system. The dramatically enhanced performance will create immediate influence on any enthusiasts.
Based on the 3G FL760 manual setup procedure, the 3GX can be setup in just a few minutes through a basic procedure. In addition, the 3GX can support all the CCPM swashplate systems presently on the marketplace including 90, 120, 135, and 140 degrees swashplates.
Supports Bluetooth connectivity- With the soon to be launched Bluetooth connectivity set, the 3GX can be set wirelessly from a PC. Ultimately there will also be smartphone apps permitting live changes to 3GX without powering down.
Custom specifications have been opened up in 3GX to permit pilots to fine tune various settings for the swashplate and rudder. The settings export feature enables customized settings to be shared among friends.
Suitable for helicopters of all class from 250 to 800, glow engine or electric powered.
With built in pirouette settlement function, the 3GX has the ability to stabilize the helicopter on a fixed point throughout pirouetting maneuvers. Pirouetting turns kind of maneuvers are easily accomplished with precision.
Support with APS gyro system and raise more functions for your helicopter. With the APS gyro, the helicopter will have the capability to self stabilize, hold position along with altitude, as well as self-governing way point flights along with return home.

Includes:
One T-Rex 600E Pro DFC with one 600 3G Carbon fiber blades set, one 600MX Brushless Motor(510KV), threeDS615 Requirement servos, one DS655 Specialized servo, one 3GX Flybarless System, oneCastle ICE HV 80 Brushless ESC, and one 6A External BEC w/ 5.1V Two-way Step-down voltage regulator

Needs:
Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
SIX Li-Po 2600 ~ 4600mAh X2 (3300mAh tip)
Digital Pitch Gauge/Dial Pitch Gauge