Align T-REX 550E DFC Super Combo Helicopter Kit w/Motor, ESC, 4 Servo

This is the Align T-REX 550E DFC Super Combo Helicopter Set. This amazing package includes not just the T-Rex 550E DFC helicopter, but also a Castle Talon 90 ESC and 600MX motor, three DS615 digital cyclic servos, a DS655 digital tail servo and the 3GX flybarless system. In addition, 520mm carbon fiber primary blades and 90mm 3k carbon fiber tail blades have actually also been included, offering you with an incredible helicopter package and a similarly impressive electronics package all in the very same box.
550E DFC Functions:
Geared up with the low CG DFC rotor head, efficiently reduces wind resistance during flight, offering the most direct and exact control feel back to the pilot, exibiting exciting 3D performance and unimaginable flight speed.
High spec MOD1 CNC helical primary gear increases gear mesh area, and decreases gear noise during flight.
Lightweight rigid metal primary shaft bearing blocks.
High quality tail transmission design, combined with dual point mounted tail pitch control assembly to lessen slops and increase rudder control accuracy.
High quality 5mm carbon rod and CNC metal tail scissor control arms are used in rudder control system to improve rudder locking and control effectiveness.
Body mount increases body rigidity and added gyro placement location.
Re-designed rear mounted rudder servo mount.
Geared up with MX series high effectiveness brushless motor.
2.0mm 3K carbon fiber side frame for simple yet rigid frame construction, enabling simple assembly and upkeep.
High speed ranked thrust bearings in tail blade grips.
High effectiveness torque tube tail drive.
Integrated swash anti-rotation guide and gyro installing platform.
Aerodynamically styled canopy for the ultimate fit.
Geared up with T-REX 600 class tail boom set, supporting with 600mm primary blades and increased tail stability
3GX Functions:
Upgraded 3GX represents the next generation of multi function flybarless system. The drastically enhanced performance will create an instant influence on any lovers.
3GX is currently the smallest and lightest flybarless system on the marketplace. Two ports to straight connect Spektrum and JR satellite receivers, along with full support of Futaba's S-BUS system.
Based upon the 3G FL760 manual setup procedure, the 3GX can be setup in a few minutes through an easy procedure. In addition, the 3GX can support all the CCPM swashplate systems currently on the marketplace consisting of 90, 120, 135, and 140 degrees swashplates.
Graphic highlighted guidelines on the computer setup software application directs the user through a step by step setup procedure, enabling fast setups without omitting any steps.
Assistance Bluetooth connection. With the soon to be released Bluetooth connection package, 3GX can be programmed wirelessly from a PC. Eventually there will also be smartphone apps allowing live modifications to 3GX without powering down.
With 3GX's integrated in Align RCE-G600 governor function, no external governor is needed, decreasing electronic wire mess.
Custom-made criteria have actually been opened up in 3GX to allow pilots to tweak numerous settings for swashplate and rudder. Settings export function enables custom settings to be shared amongst buddies.
3GX utilizes gyroscope sensing units of the greatest requirements when compared with other flybarless systems currently on the marketplace, allowing it to be used under extreme conditions. Dual axis plus rudder sensor drastically enhances swashplate and rudder correction accuracy compared with last generation 3G. This is plainly noticeable in steady hover in addition to highly aerobatic routines.
Appropriate for helicopter of all class from 200 to 700, radiance engine or electric powered. The remarkable vibration resistant quality is evident even when mounted with more difficult double sided installing tape.
3GX utilizes 16 bit processor which is 4 times faster than previous generation, along with an entirely re-written firmware. The result is a dramatic stability enhancement from previous generation, with stability that measures up to a flybarred helicopter, yet posses explosive agility.
With integrated in pirouette settlement function, 3GX has the ability to stabilize the helicopter on a set point during pirouetting maneuvers. Pirouetting flip type of maneuvers are easily performed with accuracy.
3GX's rudder enables constant rudder feel even under high speed conditions. This excellent control feel will allow pilots of all ability levels to experience the perfect combination between 3GX and helicopter.
Assistance with APS gyro system and supplies more functions for your helicopter. With the APS gyro, the helicopter will have the capability to self stabilize and hold position and altitude, in addition to self-governing method point flights and return home functions.
3GX Specifications:

Operating Temperature level: -10~60 degree

X and Y axis Operating Angle Variety: -300~+300 degree

Z axis Operating Angle Variety: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Futaba S.BUS system support: Yes

Built in governor function: Yes

Optimum working voltage: 8.5V
550E DFC Specs:

Length: 1160mm

Height: 330mm

Main Blade Length: 520mm

Main Rotor Diameter: 1188mm

Tail Rotor Diameter: 254mm

Motor Drive Gear: 11T

Main Drive Gear: 112T

Autorotation Tail Drive Gear: 131T

Tail Drive Gear: 34T

Drive Gear Ratio: 1:10.18:3.85

Weight (With Motor): 1800g
Includes:
(1) T-REX 550E DFC Set
(1) Castle Talon 90 Brushless ESC
(1) 520 Carbon fiber blade set
(3) DS615 Digital servo
(1) DS655 Digital servo
(1) 3GX Flybarless System
(1) 600MX Brushless Motor
(1) 90mm 3K Carbon Fiber Tail Blade
Needed to Total:
7-channel or more helicopter radio system
6S 2600 ~ 5200mAh Li-Po battery & compatible battery charger
Dial Pitch Gauge and different tools for assembly