Align T-REX 500X Super Combo (Metal Case Servos)

Experienced in numerous of innovations, the brand new T-REX 500X is now ready to go. More attractive and imaginative design concepts are all in here, it absolutely would be your preferred T-REX 500X design ever.

Refresh and refine, T-REX 500X adjust with brand new FL rotor head system, makes use of an extremely low CG design which decreases resistance during 3D maneuvers while increasing flight responsiveness and accuracy. A progressive design includes a gloss silver and red anodizing appearance which continue our quality development based on our 700 class helicopter. The T-REX 500X main frame makes use of composite material integration technology on carbon side frame plates, including the addition of battery mounting side rails, and a leading motor install design. Innovative adjustable belt guide sheave, permits a practical way to adjust the belt tension by releasing or tightening the screw. The screw is used to maintain optimum belt tension in time to keep the best. Likewise T-REX 500X landing skid is slanted 5 degrees forward to improve crashworthiness.

T-REX 500X makes use of 470mm main blades and 520MX(1600KV/3527) motor with 20% power upgrades than the initial 1600KV/3225 motor. The most recent new RCE-BL80X Brushless ESC assistance double BEC output from 6 ~ 8.4V offering effective and superior power. The NEW DS530M/DS535M digital servos are with severe torque and speed reaction permit to support faster, more exact and accurate flight performance.

Equipped with all the top end electronic devices, T-REX 500X is as stable and powerful like the big scale helicopters. It is about to re-define the 500-class helicopters in your mind.

New extended 470mm main blades for T-REX 500X successfully improve the flying stability and power efficiency. Improve the power for better control permit to delight in T-REX 500X flights very same like other plus size helicopters.

New 78 size tail blades are longer in length and offer superior and exact tail holding efficiency, even during demanding 3D flight.

The brand new low CG 500FL Flybarless Rotor Head System makes use of the accuracy grinding of high-carbon steel hollow shaft successfully increase its concentricity. Allow to lower resistance during 3D maneuvers, increased flight responsiveness and accuracy. In addition, the styling appearance consistency with red anodized and stainless color, highlight the high quality similar to 700 size 3D helicopter.

New Swashplate design with exact bearings features in no slop delivering a precise and accurate regulated flight.

New 520MX(1600KV/3527) motor features high effectiveness, superior power, exceptional torque, low present draw, and a low operating temperature. Allow to supply keeping consistent torque and head speed through constant 3D maneuvers.

Brand new CNC metal support plate and brace compare with frame mounting bolt successfully increase the torsional stength of main frame, under severe 3D maneuver, you can highly feel its solid support from its structure. In addition, the styling appearance consistency with red anodized and stainless color highlight the high tactile appeal.
Carbon fiber side frame plates are produced using a proprietary composite material integration technology which integrates the battery mounting rails into the frame. This special use of open spaces within the frame develops a stiff frame and is aesthetically pleasing.

An extra 3rd main shaft bearing block increases the strength of the main frame while enhancing 3D flight.

RCE-BL80X is specially designed for T-REX 500X offering higher currency output and assistance for high voltage servos with an internal BEC output from 6V to 8.4V which can be established based on servo specification.

Brand new locking battery tray which makes use of integrated mounting rails inside the frames to streamline insertion / removal of battery while offering security for the battery.

DS530M HV Cyclic and DS535M HV Rudder servos support approximately 8.4V for superior responsiveness, severe torque, and improved performance.

Innovative adjustable belt guide sheave, permits a practical way to adjust the belt tension by releasing or tightening the screw. The screw is used to maintain optimum belt tension over time.
Brand New Belt Drive Assembly design permit quiet operation and low cost on serviceability.

Ultilize of strengthen main gear case features in using larger bearing has a higher load bring capacity which decreases the loss of momentum and enhances the fficiency, speed, and smoothness of the main rotor. The new main gear case and all-metal main sheave transmission system is an effective design to provide the ultimate performance.

Landing skid is slanted 5 degrees forward to improve crashworthiness.

A 19mm wide Tail Boom to enhances the torsional strength.
Carbon Fiber Tail Control Rod is useful and enhances the helicopters tail control.

The recently designed double point supported tail control assembly delivers slop complimentary efficiency while enhancing rudder resolution and precision.

The new tail rotor holder design consists of thrust bearings which increases sturdiness, along with substantially enhancing the accuracy and effectiveness of the tail efficiency when using 78 size Tail Blades.

Specification
? Length: 935mm
? Height: 259mm
? Width: 151mm
? Main Blade Length: 470mm
? Main Rotor Diameter: 1054mm
? Tail Rotor Diameter: 219mm
? Motor Pinion Equipment: 12T
? Main Drive Equipment: 134T
? Main Drive Wheel: 80T
? Tail Own Equipment: 21T
? Own Equipment Ratio: 11.17:1:3.81
? Weight(w/o battery): approx. 1450gAccessories

?T-REX 500X PACKAGE Set x 1 
?Microbeast PLUS Flybarless System x 1 set
?470 Carbon Fiber Blades x 1
?78 Tail Rotor Blade x 1
?520MX Brushless Motor(1600KV/3527) x 1
?DS530M Digital servo x 3
?DS535M Digital servo x 1 
?RCE-BL80X Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
?Transmitter(7-channel or more, helicopter system)
?Receiver(7-channel or more)
?6S Li-Po 2600 ~ 3300mAh (3300mAh suggestion)
?Digital Pitch Gauge