Align T-REX 500 PRO DFC Super Combo Helicoper Kit w/Motor, ESC, 4 Ser

This is the Align T-REX 500 PRO DFC Flybarless Super Combination Helicopter Package. This unbelievable bundle consists of not only the T-REX 500 PRO Package, but likewise a 425 3G Carbon Fiber blade set, a 500MX Brushless motor, a RCE-BL70G Brushless Electronic Speed Controller, three DS515M cyclic servos, one DS525M tail servo and finally the amazing 3GX Programmable Flybarless System. This extremely combination offers you with an incredible helicopter kit and a similarly remarkable electronic bundle all in one box.

T-REX 500 PRO Features: The Align 500 PRO DFC helicopter is equipped with an incredibly low CG design to successfully lower wind resistance throughout flight and provide the most direct and exact control feel back to the pilot, supplying exciting 3D performance and unthinkable flight speed.
A uniquely carbon composite technology successfully enhance the weak areas and offers streamlined electronic devices setup.
The servos can be mounted directly onto the frame without mounting nuts.
The rear servo is mounted in-frame for a centralized design and optimal 3D performance.
MX series high efficiency brushless motor included with heatsink design housing and ingrained fan to significantly improve cooling and boost power output.
Distinct quick release gyro and receiver install design for quick elimination and strong accessory.
High accuracy slant tooth (helical) main equipment for higher load sustainability and lower noise output.
Redesigned tail gear box with higher material quality and easy upkeep.
High quality tail transmission design, combined with updated double point mounted tail pitch control assembly to reduce slop and boost rudder control accuracy.
Extremely effective shaft driven tail system which successfully lower power loss discovered on belt driven systems. This likewise increases performance throughout flight.
Redesigned 4mm carbon rudder control rod and metal rudder pitch bell crank to more improve the rudder locking effect and controllability.
Redesigned design battery mounting platform to enhance the frame along with to provide an install for the electronic speed controller.
Redesigned lower CG landing equipment design.
Styled aerodynamically canopy for the ultimate fit, making the helicopter stand out.
Finest tail equipment ratio to reduce vibrations triggered by the high speed operations of the main blades, bringing the best tail locking power.

3GX Programmable Flybarless System Features:

Redesigned 3GX represents the next generation of multi function flybarless systems. The significantly improved performance will develop an immediate influence on any enthusiasts.
The 3GX is presently the smallest and lightest flybarless system on the marketplace and includes 2 ports to directly connect Spektrum and JR satellite receivers, along with complete support of Futaba's S-BUS system.
Utilizing the 3G FL760 manual setup process, the 3GX can be setup simply in a matter of minutes. In addition, the 3GX can support any CCPM swashplate system presently on the marketplace consisting of 90, 120, 135, and 140 degree swashplates.
Graphically illustrated guidelines using the computer setup software directs the user as a result of an action by step setup process, allowing for fast setups without omitting any actions.
With the soon to be launched Bluetooth connectivity kit, the 3GX can be programmed wirelessly from a PC. Ultimately there will likewise be smartphone apps enabling live modifications to the 3GX without powering down.
With 3GX's built in Align RCE-G600 governor function, no external governor is needed, decreasing electronic clutter and excess wire.
A library of pre-configured 3GX settings are available for T-Rex series of helicopters, enabling pilots to accomplish the most optimal setup for their helicopter without the guesswork.
Three levels of flight mode are available to provide the ideal feel for beginner and advanced pilots.
Custom criteria have been established to permit pilots to fine tune many swashplate and rudder settings and a settings export feature allows custom settings to be shared among good friends.
The 3GX includes the highest spec gyroscope sensing units, enabling it to be used in the harshest conditions. The double axis plus rudder sensor significantly enhances swashplate and rudder correction accuracy and will be felt when hovering, along with throughout aerobatic routines.
Ideal for 200 to 700 class helicopters, glow engine or electrical powered.
The vibration resistant attributes appear even when mounted with more difficult double sided mounting tape.
16 bit processor is 4 times faster than the previous 3G, along with completely re-written firmware. The result is a remarkable enhancement in stability that measures up to a flybarred helicopter, while supplying explosive dexterity.
With an integrated in pirouette compensation function, the 3GX has the ability to stabilize the helicopter on a set point throughout pirouetting maneuvers. Pirouetting flip type of maneuvers are quickly performed with accuracy.
Rudder control is similar to the high end GP-780 gyro because the rudder level of sensitivity is enhanced for the helicopter's rudder response attributes, enabling consistent rudder feel even under high speed conditions. This outstanding control feel will permit pilots of all ability levels to experience the ideal combination in between the 3GX and the helicopter.
Additional peripherals planned for the 3GX consist of a 3-axis accelerometer, 3-axis magnetic compass, and a GPS positioning system.
The position hold gyro system uses an overall of 10 sensing units, make sure positioning of the helicopter with remarkable accuracy and supplying the ultimate solution for aerial photography and other specialized applications.
Compatible with 2 to 5 blades rotor heads
Support approximately 6 servos
Automatic servo type acknowledgment

T-REX 500 PRO Specifications:

Length: 868mm

Height: 275mm

Main Blade Length: 425mm

Main Rotor Size: 978mm

Tail Rotor Size: 206mm

Motor Drive Gear: 12T

Main Drive Gear: 134T

Autorotation Tail Drive Gear: 145T

Tail Drive Gear: 36T

Drive Gear Ratio: 1:11.17:4.03

Weight (With Motor): 1210g

3GX Specifications:

Operating Temperature level: -10~60 degree

X and Y axis Operating Angle Variety: -300~+300 degree

Z axis Operating Angle Variety: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Maximum working voltage: 8.5V 

Includes: (1) T-REX 500 PRO DFC Package
(1) 3GX Flybarless System


(1) 425 3G Carbon Fiber blades


(1) 500MX Brushless Motor (1600kV)
(3) DS515M Digital servo


(1) DS525M Digital servo


(1) RCE-BL70G Brushless ESC 

Needed to Complete:


Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
SIX LiPo Battery Load 2600 ~ 4600mAh (3300mAh recommended)
Digital Pitch Gauge