Align T-REX 500 PRO DFC Super Combo Helicoper Kit w/Motor, ESC, 4 Ser

This is the Align T-REX 500 PRO DFC Flybarless Super Combination Helicopter Kit. This incredible plan includes not only the T-REX 500 PRO Kit, but also a 425 3G Carbon Fiber blade set, a 500MX Brushless motor, a RCE-BL70G Brushless Electronic Speed Controller, three DS515M cyclic servos, one DS525M tail servo and lastly the amazing 3GX Programmable Flybarless System. This extremely combination offers you with an incredible helicopter package and an equally outstanding electronic plan all in one box.

T-REX 500 PRO Includes: The Align 500 PRO DFC helicopter is equipped with an incredibly low CG design to successfully lower wind resistance during flight and supply the most direct and exact control feel back to the pilot, supplying exhilarating 3D efficiency and inconceivable flight speed.
A uniquely carbon composite innovation successfully reinforce the weak locations and offers streamlined electronics setup.
The servos can be mounted straight onto the frame without installing nuts.
The rear servo is mounted in-frame for a centralized design and optimal 3D efficiency.
MX series high effectiveness brushless motor consisted of with heatsink style casing and ingrained fan to significantly improve cooling and boost power output.
Distinct quick release gyro and receiver install design for quick elimination and strong attachment.
High precision slant tooth (helical) primary equipment for higher load sustainability and lower sound output.
Upgraded tail transmission with higher material quality and simple maintenance.
High quality tail gearbox design, combined with upgraded double point mounted tail pitch control assembly to decrease slop and boost rudder control precision.
Extremely efficient shaft driven tail system which successfully lower power loss found on belt driven systems. This also increases efficiency during flight.
Upgraded 4mm carbon rudder control rod and metal rudder pitch bell crank to more improve the rudder locking impact and controllability.
Upgraded style battery installing platform to reinforce the frame in addition to to supply an install for the electronic speed controller.
Upgraded lower CG landing equipment style.
Styled aerodynamically canopy for the ultimate fit, making the helicopter stand out.
Finest tail equipment ratio to decrease vibrations triggered by the high speed operations of the primary blades, bringing the best tail locking power.

3GX Programmable Flybarless System Includes:

Upgraded 3GX represents the next generation of multi function flybarless systems. The significantly improved efficiency will develop an immediate influence on any lovers.
The 3GX is currently the smallest and lightest flybarless system on the marketplace and includes 2 ports to straight connect Spektrum and JR satellite receivers, along with complete assistance of Futaba's S-BUS system.
Using the 3G FL760 manual setup procedure, the 3GX can be setup just in a matter of minutes. Furthermore, the 3GX can support any CCPM swashplate system currently on the marketplace consisting of 90, 120, 135, and 140 degree swashplates.
Graphically detailed directions utilizing the computer setup software application directs the user through a step by action setup procedure, allowing for fast setups without leaving out any actions.
With the quickly to be released Bluetooth connection package, the 3GX can be configured wirelessly from a PC. Ultimately there will also be smartphone apps allowing live adjustments to the 3GX without powering down.
With 3GX's built in Align RCE-G600 guv function, no external guv is needed, decreasing electronic clutter and excess wire.
A library of pre-configured 3GX settings are readily available for T-Rex series of helicopters, allowing pilots to attain the most optimal setup for their helicopter without the guesswork.
3 levels of flight mode are readily available to supply the best feel for beginner and advanced pilots.
Customized criteria have actually been established to enable pilots to tweak various swashplate and rudder settings and a settings export function enables custom settings to be shared amongst pals.
The 3GX includes the highest spec gyroscope sensors, allowing it to be utilized in the harshest conditions. The double axis plus rudder sensor significantly improves swashplate and rudder correction precision and will be felt when hovering, in addition to during aerobatic regimens.
Appropriate for 200 to 700 class helicopters, radiance engine or electrical powered.
The vibration resistant qualities appear even when mounted with harder double sided installing tape.
16 bit processor is 4 times faster than the previous 3G, along with totally re-written firmware. The result is a dramatic improvement in stability that matches a flybarred helicopter, while supplying explosive dexterity.
With a built in pirouette compensation function, the 3GX is able to support the helicopter on a fixed point during pirouetting maneuvers. Pirouetting flip type of maneuvers are quickly performed with precision.
Rudder control resembles the high end GP-780 gyro because the rudder level of sensitivity is enhanced for the helicopter's rudder reaction qualities, allowing consistent rudder feel even under high speed conditions. This excellent control feel will enable pilots of all skill levels to experience the best combination in between the 3GX and the helicopter.
Extra peripherals planned for the 3GX include a 3-axis accelerometer, 3-axis magnetic compass, and a GPS positioning system.
The position hold gyro system utilizes a total of 10 sensors, ensure positioning of the helicopter with remarkable precision and supplying the ultimate option for aerial photography and other specialized applications.
Compatible with 2 to 5 blades rotor heads
Assistance approximately 6 servos
Automatic servo type recognition

T-REX 500 PRO Specifications:

Length: 868mm

Height: 275mm

Main Blade Length: 425mm

Main Rotor Diameter: 978mm

Tail Rotor Diameter: 206mm

Motor Drive Equipment: 12T

Main Drive Equipment: 134T

Autorotation Tail Drive Equipment: 145T

Tail Drive Equipment: 36T

Drive Equipment Ratio: 1:11.17:4.03

Weight (With Motor): 1210g

3GX Specifications:

Operating Temperature: -10~60 degree

X and Y axis Operating Angle Range: -300~+300 degree

Z axis Operating Angle Range: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Optimum working voltage: 8.5V 

Includes: (1) T-REX 500 PRO DFC Kit
(1) 3GX Flybarless System


(1) 425 3G Carbon Fiber blades


(1) 500MX Brushless Motor (1600kV)
(3) DS515M Digital servo


(1) DS525M Digital servo


(1) RCE-BL70G Brushless ESC 

Required to Total:


Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
SIX LiPo Battery Pack 2600 ~ 4600mAh (3300mAh suggested)
Digital Pitch Gauge