Align T-REX 470LM KIT (w/ Motor and ESC)

Following the release of the T-REX 450L, which presented an ingenious style and came equipped with high-end electronic devices. Align's most expected helicopter release in 2016 the T-REX 470L is born. No matter whether you are a beginner or an expert, the brand new T-REX 470L will offer you the new flying feel once again.

470EFL Main Rotor Head supplies exceptional flight stability and offers a lower CG style to decrease flying resistance while providing a more stiff and fast rotor head action. To improve the strength and sturdiness of the main and feathering shaft the 470 main shaft outer measurement was increased from Ø5mm to Ø6mm, while the feathering shaft outer measurement was increased from Ø4mm to Ø5mm. The 470L has embrace a high basic 1.2mm 3K carbon fiber main frame and a wider body style which increases the size of the battery compartment permitting the use of larger capability battery. The 470L makes use of a high effective belt drive assembly style with an ingenious adjustable belt guide sheave, providing a practical way to change the belt stress by launching or tightening up the screw. This screw is used to preserve optimum belt stress improving the life of the belt and lowering preserves costs. The landing skid is tilted 5 degrees forward to improve crashworthiness and makes T-REX470L more avant-garde and dynamic.

The T-REX 470L is equipped with the big outer size 470MX motor (1800KV) which is extremely effective providing exceptional power, excellent torque, enhanced present draw, and a lower operating temperature level which are excellent enhancements as compared to the 460MX motor.

Extended 380mm main blades effectively improve the flying stability and power performance. The new crafted airfoil style effectively reduces turbulence at the end of the main blades,this saves power usage during extreme 3D flight. New 69 size tail blades are longer in length and offer exceptional tail holding performance, even during requiring 3D flight.

Brand New 470EFL Main Rotor Head supplies exceptional flight stability and offers a lower CG style to decrease flying resistance while providing a more stiff and fast rotor head action. Brand name New 470 Main Shaft and Feathering Shaft: Main Shaft outer measurement increased from Ø5mm to Ø6mm, while the Feathering Shaft outer measurement increased from Ø4mm to Ø5mm,effectively strengthening the Main and Feathering Shaft while improving durability.

New 470MX motor functions; high effectiveness, exceptional power, excellent torque, low present draw, and a low operating temperature level. The 470MX can maintaining constant torque and head speed through constant 3D maneuvers. 470MX motor is created for 3D flight.

New Swashplate style with no slop delivering an accurate and accurate regulated flight.

Brand new CNC metal reinforcement plate and brace compare to frame installing bolt effectively increase the torsional stength of main frame, under extreme 3D maneuver, you can strongly feel its solid reinforcement from its structure.

Carbon fiber side frame plates are made utilizing a proprietary composite product combination innovation which incorporates the battery installing rails into the frame. This distinct use of open areas within the frame creates a stiff frame and is visually pleasing.

An additional 3rd main shaft bearing block increases the strength of the main frame while improving 3D flight.

Brand new latching battery tray which makes use of incorporated installing rails inside the frames to streamline insertion / removal of battery while providing protection for the battery.

Specially created for T-REX 470 providing higher currency output and support for high voltage servos with an internal BEC output from 5V to 8.4V which can be set up based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support approximately 8.4V for exceptional responsiveness, extreme torque, and enhanced performance.

Innovative adjustable belt guide sheave, permits a practical way to change the belt stress by launching or tightening up the screw. The screw is used to preserve optimum belt stress over time.

The One Method Bearing is made utilizing bearing take and after heat treatment the solidity is HRC50-55. This larger bearing has a greater load bring capability which reduces the loss of momentum and enhances the fficiency, speed, and smoothness of the main rotor. The new main gear case and all-metal main sheave transmission system is an efficient style to deliver the supreme performance.

Landing skid is tilted 5 degrees forward to improve crashworthiness.

Newly created vertical tail servo mount to improve CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to enhances the torsional strength. Carbon Fiber Tail Control Rod is practical and enhances the helicopters tail control.

Designed utilizing a proprietary product combination innovation which creates a unique look and enhances the Vertical Stabilizer's stiffness.

The newly created double point supported tail control assembly provides slop totally free performance while improving rudder resolution and precision.

The new tail rotor holder style consists of thrust bearings which increases sturdiness, as well as considerably improving the accuracy and effectiveness of the tail performance when utilizing 69 size Tail Blades.

Standard devices

?RCE-BL50X 50A Brushless ESC X 1
?470MX Brushless Motor(1800KV) X 1

Specification

?Length: 755mm
?Height: 210mm
?Width: 108mm
?Main Blade Length: 380mm
?Main Rotor Size: 850mm
?Tail Rotor Size: 181mm
?Motor Pinion Equipment: 11T
?Main Drive Equipment: 121T
?Main Drive Pulley-block: 56T
?Tail Drive Equipment: 15T
?Drive Equipment Ratio: 11:1:3.73
?Weight(w/o battery): 860gAccessories

?T-REX 470L DOMINATOR Set x 1
?380 Carbon Fiber Blades x 1set
?69 Tail Blade x1set
?470MX Brushless Motor(1800KV) x 1
?RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic devices required for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1
5.CCPM Servo X 3
6.Tail Servo X 1
7.Flybarless System x 1