Align T-REX 450 Plus DFC Super Combo BTF

Direction:
T-REX 450 has actually been the perfect choice for entry level R/C helicopters and T-REX 450 PLUS is created for beginners. The totally assembled helicopter can be flown immediately simply by plugging in a charged battery, allowing the pilot to bypass assembly and change process. This T-REX 450 PLUS DFC is a helicopter that using flybarless system.
The helicopter uses DFC rotor head assembly, coupled with 3GX MR flybarless system enhanced for T-REX 450 PLUS flight characteristics. Without any change or tuning, this combination will provide optimal stability suitable for pilots of all levels.
For those lovers who want to tweak 3GX MR even further, it can be done through a couple of simple actions. In addition, 3GX MR has a FHSS 2.4GHz receiver built in, supplying an all in one plan.
With the addition of the brand new 3GX MR, the T-REX 450 PLUS DFC presses past the efficiency restriction of flybar helicopter, improving both stability and 3D efficiency, while keeping a down to earth rate level

Instructions:(T-REX 450 Plus DFC BTF)
T-REX 450 PLUS DFC BTF（Bind To Fly）complete plan was assembled and tuned at the factory. Must utilize S-FHSS system transmitter to bind and fly. Support Futaba S-FHSS system.
Equipped with the low CG DFC rotor head, successfully decrease wind resistance during flight, supplying the most direct and precise control feel back to the pilot, and displays thrilling 3D efficiency and inconceivable flight speed.
Equipped with newly launched 3GX MR flybarless system, with FHSS 2.4GHz receiver for built in receiver function, for simpler and more direct setup, with setting enhanced for T-Rex 450 Plus DFC, leading to more steady and more preferable control feel than before.
Four piece frame plate style with anchored servo installing platform for quick servo install/removal without installing nuts.
Narrow lower frame plate and base plate style to strengthen rigidity and enhance flight agility.
Specifically created between frame rudder servo install for centralized CG area to benefit 3D flying, while reducing crash damages to rudder servo
Equipped with MX series high effectiveness brushless motor, with dramatically improved cooling effectiveness for excellent power output.
Equipped with new style REC-BL35P brushless controller featuring step-less adjustable BEC voltage between 5V to 6V .
Committed rudder gyro installing platform to separate vibration from tail transmission, improving gyro efficiency.
Recently created battery installing platform with integrated ESC install for streamlined installing of electronics.
High precision tail pitch control assembly with visually pleasing and functional style. Weighted tail blade grips successfully increases smoothness of rudder pitch action.
New style aerodynamic canopy airbrushed with vibrant graphics.

Users should have a certain concept of security to run the R/C helicopters.
Make sure to check out and adhere to associated safety notes of instruction manual before flying.

Requirements(3GX MR):
Operating Temperature level:-10~60 degree
Ideal Voltage Variety:DC 3.5~8.4V
Operating present consumption:<100mA @4.8V
Operating humidity:0%~95%
RoHS certified
X and Y axis Operating Angle Range:-300~+300 degree
Z axis Operating Angle Range:-600~+600 degree
Size:37.4x20.5x12.6 mm Size
Weight:9g Weight

Specification:(T-REX 450 Plus DFC BTF):
Length: 634mm
Height: 205mm
Main Rotor Diameter: 715mm
Tail Rotor Diameter: 158mm
Motor Drive Gear: 11T
Main Drive Gear: 112T
Autorotation Tail Drive Gear: 106T
Tail Drive Gear: 25T
Drive Gear Ratio: 1:10:4.24
Flying Weight: Approx. 584g
Color carton:27.3x10x6.6cm
Outer carton:56x31x28cm ,24sets/ctn

Accessories:
T-REX 450 Plus DFC Kit Set X1 set
3GX MR Flybarless System X1 set
325D 3G Carbon blades X1set
RCE-BL35P 35A Brushless ESC X1
450MX Brushless motor(3400KV) X1
DS415M (Metal Gear)Digital servoX3
DS425MDigital servoX1

Radio transmitter and electronic equipment required for assembly:
1.Dial Pitch Gauge or Digital Pitch Gauge
2.Swashplate Leveler
3.3S1P 11.1V 2200 mAh/30C Li-polymer Battery x 1
4.ALIGN T6 of Futaba S-FHSS 2.4G Transmitter x 1