Align Ball Link

Usage for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Several others have actually purchased this item in addition to the item that you are currently reading about.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is intended for usage with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter needs to be geared up with the inclined gear setup. To identify if your helicopter utilizes inclined gears or straight-cut gears, observe the main drive gear which will either have inclined or straight-cut teeth.



Several others have actually purchased this item in addition to the item that you are currently reading about.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is intended for usage with the Align T-Rex 550 helicopter.


Requirements:

Shape: In proportion wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Size: 4mm

Weight: 200g/set



This is a superb enhancement to the item currently being discussed.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is intended for usage with the Align T-Rex 700 Helicopter. 
Includes:

(4) 10x19x5mm Metal Shielded Bearings





Here is one more item that compliments the item being discussed.



The brand-new DELUXE swashplate leveler is designed to level the swashplate without eyeballing and thinking, permitting you to dial in the helicopter with fantastic precision & accuracy. This swashplate leveler is used for T-REX 700 Nitro helicopters, and is particularly designed for the swashplate of the Trex 700N. Due to its heavy weight, this brand-new variation is designed with a top finger rest, together with an ergonomic handle to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made from aircraft aluminum 6061-T6, and is CNC machined with the highest tolerances to eliminate any play in between the main shaft and swashplate leveler, which can result in a poorly leveled swashplate. The NEW DELUXE swashplate leveler is also anodized in silver to avoid corrosion.

Designed to work with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click here to download handbook !

This is a superb enhancement to the item currently being discussed.

Servo line Color Black and Red

Aiming to tidy up the appearance of your helicopter, aircraft of RC vehicle & safeguard your servo lines from chaffing? Servo Line Covering is an easy way to safeguard your servo wires, adding a tidy, visual want to your RC device, and can be installed in a matter of minutes. Pick from our exciting line of varied colors to add a whole new look to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply eliminate your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus giving you a flush, tight fit over the previously frayed servo covering. Do the same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly plug into your receiver. Also, be sure to bear in mind of the servo wire polarity if you cover the complete wire – this will ensure that you will know what direction to plug your servo terminal into your receiver.