Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The below item additionally pairs actually well with the item being reviewed.

4S JST-XH Lipo Balance Wire Extension Lead

This is a 4S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Numerous others have purchased this item together with the item that you are currently reviewing.

EC5 Device Connector (2)


Functions



Efficient in more than 120A continuous current with 10-awg wireErgonomically pleasing and simple to gripProtected to avoid shorting and reverse polaritySuperior innovation fit to today's innovative applicationsDesigned with convenience and dependability in mind




Overview


E-flite's high-quality EC5 ports must be a staple for every workbench. EC5 (E-flite Adapter 5mm) ports, leads with ports, and accessories are ideal for electric power applications and work with any battery, charger, ESC, Power Meter, and so on. They are ideal for high power applications.

Numerous others have purchased this item together with the item that you are currently reviewing.

EC5 Extension Lead with 6" Wire, 10Awg




Often purchased with the item that you are currently reviewing.

Servo line Color Black & Green

Wanting to tidy up the appearance of your helicopter, aircraft of RC vehicle & protect your servo lines from chaffing? Servo Line Covering is a simple way to protect your servo wires, including a tidy, visual seek to your RC device, and can be set up in a matter of minutes. Select from our amazing line of different colors to add an entire make over to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and insert the servo terminal inside. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, hence offering you a flush, tight fit over the formerly frayed servo covering. Do the exact same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly plug into your receiver. Also, be sure to keep in mind of the servo wire polarity if you cover the complete wire – this will ensure that you will know what instructions to plug your servo terminal into your receiver.

Below is a wonderful item that lots of others have purchased the same time.

Servo line Color Blue/Black (1m)

Wanting to tidy up the appearance of your helicopter, aircraft of RC vehicle & protect your servo lines from chaffing? Servo Line Covering is a simple way to protect your servo wires, including a tidy, visual seek to your RC device, and can be set up in a matter of minutes. Select from our amazing line of different colors to add an entire make over to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and insert the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, hence offering you a flush, tight fit over the formerly frayed servo covering. Do the exact same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly plug into your receiver. Also, be sure to keep in mind of the servo wire polarity if you cover the complete wire – this will ensure that you will know what instructions to plug your servo terminal into your receiver.