Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a 6S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below item also pairs truly well with the item being talked about.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Many others have actually acquired this item together with the item that you are presently reading about.

EC5 Device Connector (2)


Functions



With the ability of more than 120A continuous existing with 10-awg wireErgonomically pleasing and easy to gripProtected to prevent shorting and reverse polaritySuperior innovation fit to today's advanced applicationsDesigned with benefit and reliability in mind




Overview


E-flite's high-quality EC5 ports need to be a staple for every workbench. EC5 (E-flite Port 5mm) ports, leads with ports, and accessories are ideal for electrical power applications and deal with any battery, battery charger, ESC, Power Meter, and so on. They are ideal for high power applications.

Many others have actually acquired this item together with the item that you are presently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Often acquired with the item that you are presently reading about.

Servo line Color Black & Green

Looking to tidy up the look of your helicopter, plane of RC automobile & protect your servo lines from chaffing? Servo Line Covering is an easy method to protect your servo wires, adding a tidy, visual aim to your RC machine, and can be installed in a matter of minutes. Select from our exciting line of different colors to include a whole make over to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus giving you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make certain to remember of the servo wire polarity if you cover the full wire – this will ensure that you will understand what instructions to plug your servo terminal into your receiver.

Here is a great item that lots of others have actually bought at the same time.

Servo line Color Blue/Black (1m)

Looking to tidy up the look of your helicopter, plane of RC automobile & protect your servo lines from chaffing? Servo Line Covering is an easy method to protect your servo wires, adding a tidy, visual aim to your RC machine, and can be installed in a matter of minutes. Select from our exciting line of different colors to include a whole make over to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus giving you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make certain to remember of the servo wire polarity if you cover the full wire – this will ensure that you will understand what instructions to plug your servo terminal into your receiver.