Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below product additionally sets truly well with the product being reviewed.

4S JST-XH Lipo Balance Wire Extension Lead

This is a 4S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Several others have acquired this product together with the product that you are currently reading about.

EC5 Device Connector (2)


Functions



Capable of more than 120A continuous existing with 10-awg wireErgonomically pleasing and easy to gripProtected to avoid shorting and reverse polaritySuperior technology suited to today's sophisticated applicationsDesigned with convenience and dependability in mind




Introduction


E-flite's top quality EC5 connectors need to be a staple for every workbench. EC5 (E-flite Port 5mm) connectors, leads with connectors, and devices are perfect for electric power applications and work with any battery, charger, ESC, Power Meter, etc. They are perfect for high power applications.

Several others have acquired this product together with the product that you are currently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Often acquired with the product that you are currently reading about.

Servo line Color Black & Green

Looking to clean up the appearance of your helicopter, aircraft of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a clean, aesthetic want to your RC machine, and can be set up in a matter of minutes. Pick from our interesting line of varied colors to add an entire new look to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat gun to diminish it down around the covering, therefore offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can quickly plug into your receiver. Likewise, make certain to bear in mind of the servo wire polarity if you cover the full wire – this will ensure that you will understand exactly what instructions to plug your servo terminal into your receiver.

Below is a excellent product that several others have bought at the very same time.

Servo line Color Blue/Black (1m)

Looking to clean up the appearance of your helicopter, aircraft of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a clean, aesthetic want to your RC machine, and can be set up in a matter of minutes. Pick from our interesting line of varied colors to add an entire new look to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat gun to diminish it down around the covering, therefore offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can quickly plug into your receiver. Likewise, make certain to bear in mind of the servo wire polarity if you cover the full wire – this will ensure that you will understand exactly what instructions to plug your servo terminal into your receiver.