Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below item also sets really well with the item being talked about.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Numerous others have gotten this item together with the item that you are currently reading about.

EC5 Device Connector (2)


Functions



Capable of more than 120A continuous existing with 10-awg wireErgonomically pleasing and easy to gripProtected to avoid shorting and reverse polaritySuperior technology fit to today's innovative applicationsDesigned with benefit and reliability in mind




Introduction


E-flite's high-quality EC5 connectors need to be a staple for each workbench. EC5 (E-flite Adapter 5mm) connectors, leads with connectors, and accessories are best for electrical power applications and deal with any battery, charger, ESC, Power Meter, etc. They are perfect for high power applications.

Numerous others have gotten this item together with the item that you are currently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Frequently gotten with the item that you are currently reading about.

Servo line Color Black & Green

Wanting to clean up the look of your helicopter, airplane of RC car & protect your servo lines from chaffing? Servo Line Covering is a simple method to protect your servo wires, adding a tidy, aesthetic want to your RC maker, and can be installed in a matter of minutes. Pick from our exciting line of varied colors to add a whole make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply eliminate your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and insert the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, thus offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make certain to keep in mind of the servo wire polarity if you cover the full wire – this will make sure that you will understand what instructions to plug your servo terminal into your receiver.

Right here is a terrific item that several others have purchased the very same time.

Servo line Color Blue/Black (1m)

Wanting to clean up the look of your helicopter, airplane of RC car & protect your servo lines from chaffing? Servo Line Covering is a simple method to protect your servo wires, adding a tidy, aesthetic want to your RC maker, and can be installed in a matter of minutes. Pick from our exciting line of varied colors to add a whole make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply eliminate your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and insert the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, thus offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make certain to keep in mind of the servo wire polarity if you cover the full wire – this will make sure that you will understand what instructions to plug your servo terminal into your receiver.