Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below thing also sets actually well with the thing being reviewed.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Lots of others have actually purchased this thing along with the thing that you are currently reviewing.

EC5 Device Connector (2)


Features



Capable of more than 120A constant current with 10-awg wireErgonomically pleasing and simple to gripProtected to avoid shorting and reverse polaritySuperior innovation matched to today's innovative applicationsDesigned with benefit and reliability in mind




Introduction


E-flite's top quality EC5 connectors must be a staple for every workbench. EC5 (E-flite Port 5mm) connectors, leads with connectors, and accessories are best for electrical power applications and deal with any battery, charger, ESC, Power Meter, etc. They are ideal for high power applications.

Lots of others have actually purchased this thing along with the thing that you are currently reviewing.

EC5 Extension Lead with 6" Wire, 10Awg




Regularly purchased with the thing that you are currently reviewing.

Servo line Color Black & Green

Seeking to tidy up the look of your helicopter, aircraft of RC vehicle & secure your servo lines from chaffing? Servo Line Covering is a simple method to secure your servo wires, including a tidy, visual planning to your RC device, and can be installed in a matter of minutes. Pick from our exciting line of different colors to include an entire make over to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, hence offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can quickly connected into your receiver. Likewise, be sure to remember of the servo wire polarity if you cover the full wire – this will ensure that you will understand exactly what direction to plug your servo terminal into your receiver.

Below is a great thing that several others have actually bought at the exact same time.

Servo line Color Blue/Black (1m)

Seeking to tidy up the look of your helicopter, aircraft of RC vehicle & secure your servo lines from chaffing? Servo Line Covering is a simple method to secure your servo wires, including a tidy, visual planning to your RC device, and can be installed in a matter of minutes. Pick from our exciting line of different colors to include an entire make over to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, hence offering you a flush, tight fit over the previously frayed servo covering. Do the same with the end of your servo wire, being careful to leave the terminal bare so it can quickly connected into your receiver. Likewise, be sure to remember of the servo wire polarity if you cover the full wire – this will ensure that you will understand exactly what direction to plug your servo terminal into your receiver.