Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a 6S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The below item also sets truly well with the item being discussed.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Lots of others have actually acquired this item along with the item that you are currently reading about.

EC5 Device Connector (2)


Features



With the ability of more than 120A continuous current with 10-awg wireErgonomically pleasing and simple to gripProtected to prevent shorting and reverse polaritySuperior technology fit to today's innovative applicationsDesigned with benefit and reliability in mind




Overview


E-flite's high-quality EC5 connectors need to be a staple for every workbench. EC5 (E-flite Connector 5mm) connectors, leads with connectors, and devices are ideal for electrical power applications and work with any battery, charger, ESC, Power Meter, and so on. They are ideal for high power applications.

Lots of others have actually acquired this item along with the item that you are currently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Regularly acquired with the item that you are currently reading about.

Servo line Color Black & Green

Looking to tidy up the look of your helicopter, airplane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy way to safeguard your servo wires, including a clean, aesthetic planning to your RC maker, and can be installed in a matter of minutes. Select from our amazing line of different colors to include a whole makeover to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, hence giving you a flush, tight fit over the previously frayed servo covering. Do the very same with completion of your servo wire, taking care to leave the terminal bare so it can easily plug into your receiver. Also, be sure to remember of the servo wire polarity if you cover the complete wire – this will ensure that you will know what direction to plug your servo terminal into your receiver.

Below is a fantastic item that numerous others have actually purchased the exact same time.

Servo line Color Blue/Black (1m)

Looking to tidy up the look of your helicopter, airplane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy way to safeguard your servo wires, including a clean, aesthetic planning to your RC maker, and can be installed in a matter of minutes. Select from our amazing line of different colors to include a whole makeover to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, hence giving you a flush, tight fit over the previously frayed servo covering. Do the very same with completion of your servo wire, taking care to leave the terminal bare so it can easily plug into your receiver. Also, be sure to remember of the servo wire polarity if you cover the complete wire – this will ensure that you will know what direction to plug your servo terminal into your receiver.