Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below product likewise pairs really well with the product being gone over.

4S JST-XH Lipo Balance Wire Extension Lead

This is a 4S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Lots of others have acquired this product along with the product that you are presently reviewing.

EC5 Device Connector (2)


Functions



Capable of more than 120A continuous current with 10-awg wireErgonomically pleasing and simple to gripProtected to avoid shorting and reverse polaritySuperior technology fit to today's innovative applicationsDesigned with benefit and dependability in mind




Introduction


E-flite's high-quality EC5 adapters should be a staple for every single workbench. EC5 (E-flite Adapter 5mm) adapters, leads with adapters, and devices are best for electric power applications and work with any battery, charger, ESC, Power Meter, and so on. They are perfect for high power applications.

Lots of others have acquired this product along with the product that you are presently reviewing.

EC5 Extension Lead with 6" Wire, 10Awg




Regularly acquired with the product that you are presently reviewing.

Servo line Color Black & Green

Seeking to tidy up the look of your helicopter, airplane of RC vehicle & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a clean, visual planning to your RC maker, and can be set up in a matter of minutes. Choose from our interesting line of varied colors to add an entire make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, hence offering you a flush, tight fit over the previously frayed servo covering. Do the same with completion of your servo wire, taking care to leave the terminal bare so it can easily plug into your receiver. Also, make sure to remember of the servo wire polarity if you cover the full wire – this will make sure that you will know what direction to plug your servo terminal into your receiver.

Right here is a excellent product that lots of others have purchased the same time.

Servo line Color Blue/Black (1m)

Seeking to tidy up the look of your helicopter, airplane of RC vehicle & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a clean, visual planning to your RC maker, and can be set up in a matter of minutes. Choose from our interesting line of varied colors to add an entire make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the included heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, hence offering you a flush, tight fit over the previously frayed servo covering. Do the same with completion of your servo wire, taking care to leave the terminal bare so it can easily plug into your receiver. Also, make sure to remember of the servo wire polarity if you cover the full wire – this will make sure that you will know what direction to plug your servo terminal into your receiver.