Vortex Hobbies 3S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a THREE JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Right here is another thing that compliments the thing being talked about.

2S JST-XH Lipo Balance Wire Extension Lead (8.6 IN)

This is a TWO JST-XH Lipo Balance Wire Extension Lead

Length:8.6 Inches

Right here is another thing that compliments the thing being talked about.



Developed for usage with 3 wire Brushless motor systems, this is
    the 3.5mm Gold Bullet Connector Male from Great Planes.

FEATURES:
Gold plated

CONSISTS OF:
3 male bullet adapters

REQUIRES:
Solder and soldering iron - HCAR0776 and STAR2000

SPECS:
Length: .47" (12mm)
Diameter: .14" (3.5mm) outside

COMMENTS:
For the 3.5mm female adapter order GPMM3113

This thing compliments the above talked about thing.

11x7 Thin Electric Prop

This is a 11x7E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered aircraft only (not for glow engines).

FEATURES:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 5 adapter rings that adapt to different motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
Five composite adapter rings

REQUIRES:
ALL props require balancing, this is CRUCIAL, use TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5006 (Metric)

SPECS:
Diameter: 11"
Pitch: 7
Hub inner diameter: 0.25"

Numerous others have gotten this thing along with the thing that you are presently checking out.

Venom Power Charger Lead w/EC3

This is the Venom EC3 Male to Battery charger Adapter.

FEATURES:
Connects a battery with an EC3 male plug to a battery charger with 4mm
    input jacks
14 AWG wire

CONSISTS OF:
11.75" (298mm) wire lead with 4mm banana plugs and EC3

Numerous others have gotten this thing along with the thing that you are presently checking out.



These are Female 2-Pin Flat Red Connectors with 3" wires.
This is also referred to as a JST connector.

FEATURES:
Developed for usage with the majority of Park Flyer ElectriFly electronic devices
Red 2-pin flat adapter is a BEC-style
Wires are 24 gauge and pre-tinned at ends for easy soldering
One year quality period

CONSISTS OF:
Two Female 2-Pin Red Connectors with 3" wires

REQUIRES:
Soldering to connect wires to application

SPECS:
Plug Size-
    Length: 19mm (general)
    Width: 7mm
    Height: 4mm

COMMENTS:
For the male adapters with wire, usage GPMM3106.
This adapter can be utilized to replace BEC-type adapters.

Often gotten with the thing that you are presently checking out.

10X6 Thin Electric Prop

This is a 10x6E Thin Composite propeller from Advanced Accuracy Composites
For usage on Electric powered aircraft

FEATURES:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 5 adapter rings that fit into propeller hub to enable
for different motor shaft diameters.

INCLUDES:
One composite propeller
Five composite adapter rings
Guideline sheet

REQUIRES:
All props require balancing. The Leading Flite Power Point Propeller
Balancer (TOPQ5700) can be utilized for this purpose.
If prop reamer needed, use GPMQ5005 (SAE) or GPMQ5007 (Metric).

SPECS:
Diameter: 10" (250mm)
Pitch: 6
Hub inner diameter: 0.25" (6.4mm)
Adapter sizes: 3.3mm (1/8"), 4mm (5/32"), 4.9mm (3/16"),
6.0mm (1/4"), 8.0mm (5/16")

COMMENTS:
This propeller should not be utilized on gas or glow engines.