Vortex Hobbies 3S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a THREE JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Below is another product that praises the product being discussed.

2S JST-XH Lipo Balance Wire Extension Lead (8.6 IN)

This is a TWO JST-XH Lipo Balance Wire Extension Lead

Length:8.6 Inches

Below is another product that praises the product being discussed.



Created for usage with 3 wire Brushless motor systems, this is
    the 3.5mm Gold Bullet Connector Male from Great Planes.

FEATURES:
Gold plated

CONSISTS OF:
3 male bullet connectors

NEEDS:
Solder and soldering iron - HCAR0776 and STAR2000

SPECIFICATIONS:
Length: .47" (12mm)
Diameter: .14" (3.5mm) outside

REMARKS:
For the 3.5mm female port order GPMM3113

This product praises the above discussed product.

11x7 Thin Electric Prop

This is a 11x7E Thin Composite propeller from Advanced Precision Composites.
For use on Electric powered airplane only (not for radiance engines).

FEATURES:
Gray composite propeller blades that put together onto a propeller hub.
Comes with five adapter rings that adapt to different motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
Five composite adapter rings

NEEDS:
ALL props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5006 (Metric)

SPECIFICATIONS:
Diameter: 11"
Pitch: 7
Center inner size: 0.25"

Numerous others have actually purchased this product in addition to the product that you are presently reading about.

Venom Power Charger Lead w/EC3

This is the Venom EC3 Male to Charger Adapter.

FEATURES:
Connects a battery with an EC3 male plug to a charger with 4mm
    input jacks
14 AWG wire

CONSISTS OF:
11.75" (298mm) wire lead with 4mm banana plugs and EC3

Numerous others have actually purchased this product in addition to the product that you are presently reading about.



These are Female 2-Pin Flat Red Connectors with 3" wires.
This is likewise called a JST connector.

FEATURES:
Created for usage with most Park Flyer ElectriFly electronics
Red 2-pin flat port is a BEC-style
Wires are 24 gauge and pre-tinned at ends for simple soldering
One year quality assurance

CONSISTS OF:
Two Female 2-Pin Red Connectors with 3" wires

NEEDS:
Soldering to connect wires to application

SPECIFICATIONS:
Plug Size-
    Length: 19mm (general)
    Width: 7mm
    Height: 4mm

REMARKS:
For the male connectors with wire, usage GPMM3106.
This port can be utilized to replace BEC-type connectors.

Frequently purchased with the product that you are presently reading about.

10X6 Thin Electric Prop

This is a 10x6E Thin Composite propeller from Advanced Precision Composites
For usage on Electric powered airplane

FEATURES:
Gray composite propeller blades that put together onto a propeller hub.
Comes with five adapter rings that fit into propeller hub to enable
for different motor shaft diameters.

INCLUDES:
One composite propeller
Five composite adapter rings
Direction sheet

NEEDS:
All props need balancing. The Top Flite Power Point Propeller
Balancer (TOPQ5700) can be utilized for this purpose.
If prop reamer required, use GPMQ5005 (SAE) or GPMQ5007 (Metric).

SPECIFICATIONS:
Diameter: 10" (250mm)
Pitch: 6
Center inner size: 0.25" (6.4mm)
Adapter sizes: 3.3mm (1/8"), 4mm (5/32"), 4.9mm (3/16"),
6.0mm (1/4"), 8.0mm (5/16")

REMARKS:
This propeller must not be utilized on gas or radiance engines.