Traxxas Wheelie Bar Mnt Stamp/Rust/Bandit

    This is an optional Wheelie Bar Mount for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, black in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    place

INCLUDES:
Assembled optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Get this thing to enhance the one you are reading about.

Bumper, Rear/ Slash

This is the Back Bumper and Mount for the
Traxxas Slash 1/10 2WD Short Course Racing Truck.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Back Bumper and bumper install

REQUIRES:
Setup on the Traxxas Slash

This is a great enhancement to the thing presently being reviewed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building

INCLUDES:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECIFICATIONS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

REMARKS:
None

This thing compliments the main item below.

3 X 15Mm Button Hex Screw (6)

This is a plan of 6 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Utilized on the Traxxas Revo beast truck, can also be utilized in any
    application where a 3x15mm button head screw is needed

INCLUDES:
Six 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECIFICATIONS:
Length: 15mm
Diameter: 3mm

Frequently purchased with the thing that you are presently checking out.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FEATURES:
Black steel building

INCLUDES:
Six steel shoulder screws

SPECIFICATIONS:
Length: 12mm
Diameter: 3mm

Frequently purchased with the thing that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing compliments the above reviewed thing.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building

INCLUDES:
Two 48mm pins
Two 34mm pins
Two 30mm pins
Two 28mm pins
Two 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Outlaw

REMARKS:
For a total suspension pin set order TRAC4940

This thing is often purchased with the above stated thing.

Wheelie Bar Mount (1) Hardware (Blue)

This is an optional Wheelie Bar Mount in Blue for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, blue in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    place

INCLUDES:
Assembled optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Right here is another thing that compliments the thing being reviewed.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon building
Replaces a worn or broken bellcrank set
May also be installed on the Traxxas Rustler, Outlaw and 2WD Slash
    models (assembled in different setups depending on model)

INCLUDES:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
Two Servo Arms
Two Shoulder Screws
Two 3x15 Counter Sunk Machine Screws
Two Hollow Balls
4 Bushings
Direction Sheet

REQUIRES:
Assembly and setup following the model handbook and included
guideline sheet