Traxxas Wheelie Bar Mnt Stamp/Rust/Bandit

    This is an optional Wheelie Bar Mount for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, black in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    place

INCLUDES:
Put together optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Get this item to enhance the one you are reading around.

Bumper, Rear/ Slash

This is the Back Bumper and Mount for the
Traxxas Slash 1/10 2WD Short Course Racing Truck.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Back Bumper and bumper mount

REQUIRES:
Setup on the Traxxas Slash

This is a great addition to the item currently being reviewed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building and construction

INCLUDES:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECIFICATIONS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

COMMENTS:
None

This item compliments the main item here.

3 X 15Mm Button Hex Screw (6)

This is a package of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Utilized on the Traxxas Revo monster truck, can also be utilized in any
    application where a 3x15mm button head screw is needed

INCLUDES:
6 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECIFICATIONS:
Length: 15mm
Diameter: 3mm

Often gotten with the item that you are currently checking out.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FEATURES:
Black steel building

INCLUDES:
6 steel shoulder screws

SPECIFICATIONS:
Length: 12mm
Diameter: 3mm

Often gotten with the item that you are currently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item compliments the above reviewed item.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Long lasting steel building

INCLUDES:
2 48mm pins
2 34mm pins
2 30mm pins
2 28mm pins
2 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Outlaw

COMMENTS:
For a total suspension pin set order TRAC4940

This item is regularly gotten with the above mentioned item.

Wheelie Bar Mount (1) Hardware (Blue)

This is an optional Wheelie Bar Mount in Blue for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, blue in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    place

INCLUDES:
Put together optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Below is an additional item that compliments the item being reviewed.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon building
Replaces a used or damaged bellcrank set
May also be installed on the Traxxas Rustler, Outlaw and 2WD Slash
    designs (assembled in various setups depending upon model)

INCLUDES:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Machine Screws
2 Hollow Balls
4 Bushings
Direction Sheet

REQUIRES:
Assembly and installation following the model manual and consisted of
instruction sheet