Traxxas Wheelie Bar Mnt Stamp/Rust/Bandit

    This is an optional Wheelie Bar Mount for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of solidified plastic, black in color
Installs at rear of chassis to hold wheelie bar arm and wheels in
    place

CONSISTS OF:
Assembled optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Get this thing to boost the one you are reading around.

Bumper, Rear/ Slash

This is the Back Bumper and Mount for the
Traxxas Slash 1/10 2WD Short Course Racing Truck.

FEATURES:
Nylon building
Black in color

CONSISTS OF:
One Back Bumper and bumper mount

REQUIRES:
Setup on the Traxxas Slash

This is a great enhancement to the thing currently being discussed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FUNCTIONS:
Fiberglass Building and construction

CONSISTS OF:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Thickness: 2.0 mm (0.082")

COMMENTS:
None

This thing compliments the main item below.

3 X 15Mm Button Hex Screw (6)

This is a bundle of 6 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Utilized on the Traxxas Revo monster truck, can also be utilized in any
    application where a 3x15mm button head screw is required

CONSISTS OF:
Six 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Diameter: 3mm

Regularly gotten with the thing that you are currently checking out.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FUNCTIONS:
Black steel building

CONSISTS OF:
Six steel shoulder screws

SPECS:
Length: 12mm
Diameter: 3mm

Regularly gotten with the thing that you are currently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This thing compliments the above discussed thing.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FUNCTIONS:
Resilient steel building

CONSISTS OF:
2 48mm pins
2 34mm pins
2 30mm pins
2 28mm pins
2 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Outlaw

COMMENTS:
For a total suspension pin set order TRAC4940

This thing is frequently gotten with the above stated thing.

Wheelie Bar Mount (1) Hardware (Blue)

This is an optional Wheelie Bar Mount in Blue for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of solidified plastic, blue in color
Installs at rear of chassis to hold wheelie bar arm and wheels in
    place

CONSISTS OF:
Assembled optional Wheelie Bar Mount with mounting instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Below is an additional thing that compliments the thing being discussed.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FUNCTIONS:
Composite nylon building
Changes a worn or damaged bellcrank set
May also be installed on the Traxxas Rustler, Outlaw and 2WD Slash
    designs (put together in various setups depending on model)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Device Screws
2 Hollow Balls
Four Bushings
Guideline Sheet

REQUIRES:
Assembly and installation following the model manual and consisted of
guideline sheet