Traxxas Wheelie Bar Mnt Stamp/Rust/Bandit

    This is an optional Wheelie Bar Mount for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, black in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    location

CONSISTS OF:
Assembled optional Wheelie Bar Mount with installing instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Get this item to enhance the one you are reading about.

Bumper, Rear/ Slash

This is the Rear Bumper and Mount for the
Traxxas Slash 1/10 2WD Short Course Racing Truck.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Rear Bumper and bumper install

REQUIRES:
Setup on the Traxxas Slash

This is a superb enhancement to the item presently being reviewed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building

CONSISTS OF:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

COMMENTS:
None

This item praises the main item right here.

3 X 15Mm Button Hex Screw (6)

This is a bundle of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel construction, Black in color
Utilized on the Traxxas Revo beast truck, can also be utilized in any
    application where a 3x15mm button head screw is required

CONSISTS OF:
Six 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm

Often bought with the item that you are presently reading about.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FEATURES:
Black steel construction

CONSISTS OF:
Six steel shoulder screws

SPECS:
Length: 12mm
Size: 3mm

Often bought with the item that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item praises the above reviewed item.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel construction

CONSISTS OF:
2 48mm pins
2 34mm pins
2 30mm pins
2 28mm pins
2 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Bandit

COMMENTS:
For a complete suspension pin set order TRAC4940

This item is frequently bought with the above discussed item.

Wheelie Bar Mount (1) Hardware (Blue)

This is an optional Wheelie Bar Mount in Blue for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, blue in color
Installs at back of chassis to hold wheelie bar arm and wheels in
    location

CONSISTS OF:
Assembled optional Wheelie Bar Mount with installing instructions and
    hardware

REQUIRES:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Here is one more item that praises the item being reviewed.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon construction
Changes a used or damaged bellcrank set
May also be set up on the Traxxas Rustler, Bandit and 2WD Slash
    designs (assembled in various configurations depending upon design)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Machine Screws
2 Hollow Balls
4 Bushings
Guideline Sheet

REQUIRES:
Assembly and setup following the design manual and included
guideline sheet