Traxxas Wheelie Bar Mnt Stamp/Rust/Bandit

    This is an optional Wheelie Bar Mount for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, black in color
Installs at rear of chassis to hold wheelie bar arm and wheels in
    location

INCLUDES:
Assembled optional Wheelie Bar Mount with installing directions and
    hardware

NEEDS:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Get this product to boost the one you are reading about.

Bumper, Rear/ Slash

This is the Rear Bumper and Mount for the
Traxxas Slash 1/10 2WD Short Course Racing Truck.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Rear Bumper and bumper install

NEEDS:
Installation on the Traxxas Slash

This is a fantastic addition to the product presently being gone over.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Construction

INCLUDES:
One Tie Bar

NEEDS:
Suspension Pins (TRAC4940)

SPECIFICATIONS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

COMMENTS:
None

This product praises the main item below.

3 X 15Mm Button Hex Screw (6)

This is a plan of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel construction, Black in color
Used on the Traxxas Revo beast truck, can likewise be utilized in any
    application where a 3x15mm button head screw is needed

INCLUDES:
Six 3x15mm Traxxas Button Head Screws

NEEDS:
2mm hex head wrench, GPMR8011

SPECIFICATIONS:
Length: 15mm
Size: 3mm

Often bought with the product that you are presently checking out.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FEATURES:
Black steel construction

INCLUDES:
Six steel shoulder screws

SPECIFICATIONS:
Length: 12mm
Size: 3mm

Often bought with the product that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This product praises the above gone over product.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Durable steel construction

INCLUDES:
Two 48mm pins
Two 34mm pins
Two 30mm pins
Two 28mm pins
Two 25mm pins

NEEDS:
Installation on the Rustler, Stampede or Bandit

COMMENTS:
For a total suspension pin set order TRAC4940

This product is frequently bought with the above pointed out product.

Wheelie Bar Mount (1) Hardware (Blue)

This is an optional Wheelie Bar Mount in Blue for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, blue in color
Installs at rear of chassis to hold wheelie bar arm and wheels in
    location

INCLUDES:
Assembled optional Wheelie Bar Mount with installing directions and
    hardware

NEEDS:
Wheelie Bar Arm (TRAC9574)
Wheels and Axles (TRAC9576)

Here is one more product that praises the product being gone over.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon construction
Replaces a worn or broken bellcrank set
May likewise be set up on the Traxxas Rustler, Bandit and 2WD Slash
    models (put together in various configurations depending upon model)

INCLUDES:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
Two Servo Arms
Two Shoulder Screws
Two 3x15 Counter Sunk Device Screws
Two Hollow Balls
Four Bushings
Direction Sheet

NEEDS:
Assembly and setup following the model handbook and included
instruction sheet