Traxxas Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Numerous others have bought this thing along with the thing that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have bought this thing along with the thing that you are presently checking out.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

Here is a fantastic thing that several others have bought at the very same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

The below thing also sets truly well with the thing being discussed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This thing compliments the main item below.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Setup on car

You will certainly love this product if you have the product just above discussed.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits numerous Traxxas
cars. .
Includes: 1 equipment only

The below thing also sets truly well with the thing being discussed.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

Numerous others have bought this thing along with the thing that you are presently checking out.

Metal Washers/12

These are 3x6mm Washers from Traxxas.

FEATURES:
Metal building and construction

INCLUDES:
(12) Washers

SPECIFICATIONS:
Size: 3x6mm

Numerous others have bought this thing along with the thing that you are presently checking out.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

This is a superb enhancement to the thing presently being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL variation of both the Stampede
and Rustler.