Traxxas Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Numerous others have actually acquired this item along with the item that you are currently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have actually acquired this item along with the item that you are currently reading about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

Below is a terrific item that lots of others have actually purchased the same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

The below item additionally pairs truly well with the item being reviewed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This item praises the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

REQUIRES:
Installation on automobile

You will certainly enjoy this item if you have the item previously mentioned.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits several Traxxas
vehicles. .
Consists of: 1 gear just

The below item additionally pairs truly well with the item being reviewed.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

Numerous others have actually acquired this item along with the item that you are currently reading about.

Metal Washers/12

These are 3x6mm Washers from Traxxas.

FEATURES:
Metal construction

CONSISTS OF:
(12) Washers

SPECIFICATIONS:
Size: 3x6mm

Numerous others have actually acquired this item along with the item that you are currently reading about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

This is a great addition to the item currently being reviewed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.