Traxxas Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Lots of others have gotten this product along with the product that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Lots of others have gotten this product along with the product that you are presently checking out.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

Right here is a wonderful product that numerous others have bought at the exact same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

The below product additionally sets actually well with the product being reviewed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This product compliments the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Installation on vehicle

You will certainly enjoy this product if you have the product earlier stated.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits several Traxxas
automobiles. .
Includes: 1 equipment just

The below product additionally sets actually well with the product being reviewed.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, use
    TRAC2536.

Lots of others have gotten this product along with the product that you are presently checking out.

Metal Washers/12

These are 3x6mm Washers from Traxxas.

FEATURES:
Metal building and construction

CONSISTS OF:
(12) Washers

SPECIFICATIONS:
Size: 3x6mm

Lots of others have gotten this product along with the product that you are presently checking out.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This is a great enhancement to the product presently being reviewed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.