Traxxas Suspension Pins 44Mm Slash Rustler / Stampede / Bandit

This is a pair of chrome suspension pins used to hold the front suspension arms
on the TRAXXAS SRT, NITRO STAMPEDE, and NITRO RUSTLER.

Includes: 2 chrome suspension pins and three "E" type retaining clips.

Requires:absolutely nothing parts are a direct replacement.

Specs:3mm x 44mm pins are notched for the 3MM "E" type retaining clips at each
end. WLG 9-29-97

This is a wonderful addition to the item presently being reviewed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building

INCLUDES:
One Tie Bar

NEEDS:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

REMARKS:
None

Below is a fantastic item that numerous others have actually purchased the same time.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Long lasting steel building

INCLUDES:
Two 48mm pins
Two 34mm pins
Two 30mm pins
Two 28mm pins
Two 25mm pins

NEEDS:
Installation on the Rustler, Stampede or Outlaw

REMARKS:
For a total suspension pin set order TRAC4940

This item compliments the above reviewed item.

Front Bulkhead (Black) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in lots of Traxxas vehicles.
The front suspension arm hinge pins go through this piece.

FEATURES:
Black nylon building

INCLUDES:
One front bulkhead

NEEDS:
Absolutely nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

REMARKS:
This part is used on the following automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede.

This item compliments the above reviewed item.

Front Bulkhead (Gray) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in lots of Traxxas vehicles.
The front suspension arm hinge pins pass through this piece.

FEATURES:
Gray nylon building

INCLUDES:
One front bulkhead

NEEDS:
Absolutely nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

REMARKS:
This part is used on the following automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede,
    Rustler XL and Stampede XL.

Below is a fantastic item that numerous others have actually purchased the same time.

Wide Front Bumper, For Traxxas Rustler/Stampede/ Nitro Sport/Ban

This is a Wide Front Bumper for the Traxxas Rustler and Stampede.
The Bumper goes on the Front of the Vehicle and Protects the Chassis.

FEATURES:
Long lasting Plastic Building
Black in Color

INCLUDES:
One Bumper
One Group RPM Decal

NEEDS:
Installation onto the Traxxas Rustler or Stampede.

SPECS:
Length: 2-3/4"
Width: 6-1/8"

REMARKS:
The Factory Number is #81162

Below is a fantastic item that numerous others have actually purchased the same time.

Rod Ends Long & Short

This set of rod ends, balls, and screws is used on all but 4 of Traxxas'
packages. It WILL NOT DEAL WITH: the Sledgehammer, initial Hawk, Cat, or Bullet.

Includes: 4 short rod ends (17mm)
16 long rod ends (19mm)
2 ball screws
18 hollow ball adapters

pcd 01/23/94