Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

CONSISTS OF:
2 rear stub axles and pins

SPECIFICATIONS:
Length: 1.65" (42mm)
Size: .51" (13mm) at biggest point

Below is an additional item that praises the item being talked about.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made from two pieces)
4 aluminum U-joints

pcd 01/23/94

Below is an additional item that praises the item being talked about.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for use on Traxxas trucks.

Features: White plastic parts

Consists of:
(6) sets of drive shafts (each set includes a within shaft wich
slides in the outside shaft).

Measurements: 2.5" long when totally compressed.

Requires: Absolutely nothing else needed

This item is regularly acquired with the above stated item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a fantastic item that several others have purchased the very same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
guiding knuckles attach to.

FEATURES:
Nylon building, black in color
Stamped right and delegated insure appropriate installation

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly between A-arms and guiding knuckles

The below item also pairs really well with the item being talked about.



This is the ST Racing Silver Aluminum Back Center Provider
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

CONSISTS OF:
One Silver Aluminum Back Center Provider

Below is a fantastic item that several others have purchased the very same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock including the shock oil.

FEATURES:
Nylon building

CONSISTS OF:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

NEEDS:
Other shock parts

SPECIFICATIONS:
Size Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Numerous others have acquired this item in addition to the item that you are presently reading about.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Provider that comes consisted of with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear hub or hub carrier.
Has 2 possible install locations for the external hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the two 5x8mm bushings (or bearings) on the stub
axle also called the wheel shaft.

AXY
3/25/95

Below is a fantastic item that several others have purchased the very same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Outlaw, Stampede and Rustler VXL.

FEATURES:
Black plastic building

CONSISTS OF:
2 differntial output yokes
2 3x5mm countersunk screws
2 screw pins

NEEDS:
Installation

SPECIFICATIONS:
Length: .70" (18mm)
Size: .51" (13mm)