Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal construction, black and silver in color

CONSISTS OF:
Two rear stub axles and pins

SPECS:
Length: 1.65" (42mm)
Size: .51" (13mm) at biggest point

Right here is one more thing that compliments the thing being reviewed.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made of two pieces)
4 aluminum U-joints

pcd 01/23/94

Right here is one more thing that compliments the thing being reviewed.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for use on Traxxas trucks.

Features: White plastic parts

Consists of:
(6) sets of drive shafts (each set includes an inside shaft wich
slides in the outdoors shaft).

Dimensions: 2.5" long when totally compressed.

Requires: Absolutely nothing else needed

This thing is frequently purchased with the above mentioned thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Right here is a wonderful thing that many others have purchased the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is what the
steering knuckles attach to.

FEATURES:
Nylon construction, black in color
Stamped right and delegated insure appropriate setup

CONSISTS OF:
Two RPM 30° Front Caster Blocks

NEEDS:
Assembly between A-arms and steering knuckles

The listed below thing likewise sets actually well with the thing being reviewed.



This is the ST Racing Silver Aluminum Back Center Carrier
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

CONSISTS OF:
One Silver Aluminum Back Center Carrier

Right here is a wonderful thing that many others have purchased the same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock containing the shock oil.

FEATURES:
Nylon construction

CONSISTS OF:
Two nylon shock cap (tops)
Two nylon shock cap (bottoms)

NEEDS:
Other shock parts

SPECS:
Size Tops Bottoms
16MM 13MM

REMARKS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Lots of others have purchased this thing along with the thing that you are currently reviewing.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Carrier that comes consisted of with
the Rustler and Stampede trucks.

FEATURES:
Made from a black plastic/nylon material.
Also called the rear center or center carrier.
Has 2 possible install areas for the outer hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the two 5x8mm bushings (or bearings) on the stub
axle likewise called the wheel shaft.

AXY
3/25/95

Right here is a wonderful thing that many others have purchased the same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Outlaw, Stampede and Rustler VXL.

FEATURES:
Black plastic construction

CONSISTS OF:
Two differntial output yokes
Two 3x5mm countersunk screws
Two screw pins

NEEDS:
Setup

SPECS:
Length: .70" (18mm)
Size: .51" (13mm)