Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

INCLUDES:
2 rear stub axles and pins

SPECS:
Length: 1.65" (42mm)
Size: .51" (13mm) at largest point

Here is an additional thing that praises the thing being talked about.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made from two pieces)
4 aluminum U-joints

pcd 01/23/94

Here is an additional thing that praises the thing being talked about.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for usage on Traxxas trucks.

Features: White plastic parts

Includes:
(6) sets of drive shafts (each set consists of a within shaft wich
slides in the outdoors shaft).

Measurements: 2.5" long when completely compressed.

Requires: Absolutely nothing else required

This thing is regularly gotten with the above pointed out thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a wonderful thing that lots of others have actually purchased the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and delegated insure right installation

INCLUDES:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly between A-arms and steering knuckles

The listed below thing likewise sets actually well with the thing being talked about.



This is the ST Racing Silver Aluminum Rear Hub Provider
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

INCLUDES:
One Silver Aluminum Rear Hub Provider

Here is a wonderful thing that lots of others have actually purchased the same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock containing the shock oil.

FEATURES:
Nylon building

INCLUDES:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

NEEDS:
Other shock components

SPECS:
Size Tops Bottoms
16MM 13MM

REMARKS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Lots of others have actually gotten this thing in addition to the thing that you are presently reading about.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Provider that comes consisted of with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear hub or hub carrier.
Has 2 possible install locations for the external hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the two 5x8mm bushings (or bearings) on the stub
axle also called the wheel shaft.

AXY
3/25/95

Here is a wonderful thing that lots of others have actually purchased the same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Bandit, Stampede and Rustler VXL.

FEATURES:
Black plastic building

INCLUDES:
2 differntial output yokes
2 3x5mm countersunk screws
2 screw pins

NEEDS:
Setup

SPECS:
Length: .70" (18mm)
Size: .51" (13mm)