Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a amazing enhancement to the thing presently being reviewed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Below is one more thing that praises the thing being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This thing praises the main item below.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, use
    TRAC2536.

Below is a wonderful thing that lots of others have actually bought at the same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This thing is regularly acquired with the above stated thing.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

The below thing also sets really well with the thing being reviewed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want one more wonderful thing to compliment the above stated thing?

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits several Traxxas
vehicles. .
Includes: 1 equipment only

This thing is regularly acquired with the above stated thing.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Installation on automobile

This thing is regularly acquired with the above stated thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile