Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a superb enhancement to the thing presently being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Below is one more thing that compliments the thing being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing compliments the main item right here.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
2 front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

Below is a fantastic thing that numerous others have bought at the same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This thing is often bought with the above pointed out thing.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

The below thing additionally sets actually well with the thing being talked about.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want one more fantastic thing to match the above pointed out thing?

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits numerous Traxxas
automobiles. .
Includes: 1 gear just

This thing is often bought with the above pointed out thing.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Installation on car

This thing is often bought with the above pointed out thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on car