Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a superb addition to the item presently being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Here is one more item that praises the item being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This item praises the main item below.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building
Natural color

CONSISTS OF:
2 front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

Here is a terrific item that lots of others have actually purchased the very same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

This item is often bought with the above mentioned item.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

The listed below item also pairs truly well with the item being talked about.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want one more terrific item to match the above mentioned item?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits numerous Traxxas
cars. .
Includes: 1 equipment just

This item is often bought with the above mentioned item.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Installation on car

This item is often bought with the above mentioned item.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car