Traxxas Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
Two steering blocks

NEEDS:
Installation on steering assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will certainly enjoy this thing if you have the thing earlier discussed.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
One left caster block
One right caster block

NEEDS:
Installation on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

Get this product to enhance the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want one more terrific product to enhance the above discussed product?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

INCLUDES:
Two Ball Bearings

NEEDS:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one needed).

Frequently purchased with the product that you are currently checking out.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Front driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

Right here is one more product that compliments the product being talked about.

Stub Axle Housing (2)

These are the axle housings (or center providers) used on the: Rad 2, Hawk 2,
Eagle, Blue Eagle LS II and Nitro Rustler. The housings are molded of
black nylon.

Includes: 2 axle housings

pcd 01/23/94

Right here is a terrific product that several others have actually purchased the very same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

The listed below product additionally pairs truly well with the product being talked about.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas cars
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum construction

INCLUDES:
Two hex hubs
4 axle pins

NEEDS:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

REMARKS:
These hubs might be used with other cars utilizing the very same
    pin/hex design. These hubs Will Not work on the T-Maxx or E-Maxx.

This product is regularly purchased with the above discussed product.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two rear 49mm (82mm center to center) turnbuckles

NEEDS:
Installation on the automobile

This product is regularly purchased with the above discussed product.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two front 39mm (69mm center to center) turnbuckles and guideline
    sheet

NEEDS:
Installation on the automobile