Traxxas Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic building
Black in color

CONSISTS OF:
2 steering blocks

NEEDS:
Setup on steering assembly

SPECIFICATIONS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will like this item if you have the item previously pointed out.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic building
Black in color

CONSISTS OF:
One left caster block
One right caster block

NEEDS:
Setup on Slash

SPECIFICATIONS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

Get this product to improve the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional fantastic product to enhance the above discussed product?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to car

SPECIFICATIONS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one needed).

Frequently purchased with the product that you are currently reviewing.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Front driveshaft assembly
Screw pin

NEEDS:
Setup on car

Here is an additional product that compliments the product being gone over.

Stub Axle Housing (2)

These are the axle real estates (or hub providers) used on the: Rad 2, Hawk 2,
Eagle, Blue Eagle LS II and Nitro Rustler. The real estates are molded of
black nylon.

Includes: 2 axle real estates

pcd 01/23/94

Here is a fantastic product that several others have actually purchased the exact same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

The listed below product also sets actually well with the product being gone over.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas vehicles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum building

CONSISTS OF:
2 hex hubs
4 axle pins

NEEDS:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

REMARKS:
These hubs could be used with other vehicles using the same
    pin/hex design. These hubs Will Not deal with the T-Maxx or E-Maxx.

This product is regularly purchased with the above discussed product.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
2 rear 49mm (82mm center to center) turnbuckles

NEEDS:
Setup on the car

This product is regularly purchased with the above discussed product.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Hyperlinks
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
2 front 39mm (69mm center to center) turnbuckles and guideline
    sheet

NEEDS:
Setup on the car