Traxxas Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

CONSISTS OF:
Two steering blocks

REQUIRES:
Setup on guiding assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will enjoy this item if you have the item earlier mentioned.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

CONSISTS OF:
One left caster block
One right caster block

REQUIRES:
Setup on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

Get this product to boost the one you are reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Want another great product to compliment the above mentioned product?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are utilized to support the Primary Clutch (one required).

Frequently purchased with the product that you are currently reading about.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Here is another product that praises the product being gone over.

Stub Axle Housing (2)

These are the axle housings (or center carriers) utilized on the: Rad 2, Hawk 2,
Eagle, Blue Eagle LS II and Nitro Rustler. The housings are molded of
black nylon.

Includes: 2 axle housings

pcd 01/23/94

Here is a great product that numerous others have actually purchased the very same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

The below product additionally sets really well with the product being gone over.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas vehicles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum construction

CONSISTS OF:
Two hex centers
4 axle pins

REQUIRES:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

REMARKS:
These centers might be utilized with other vehicles making use of the same
    pin/hex design. These centers Will Not deal with the T-Maxx or E-Maxx.

This product is regularly purchased with the above mentioned product.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the automobile

This product is regularly purchased with the above mentioned product.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Hyperlinks
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and direction
    sheet

REQUIRES:
Setup on the automobile