Traxxas Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building
Black in color

CONSISTS OF:
2 steering obstructs

NEEDS:
Setup on guiding assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will enjoy this item if you have the item earlier discussed.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building
Black in color

CONSISTS OF:
One left caster block
One right caster block

NEEDS:
Setup on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

Get this product to boost the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional wonderful product to compliment the above stated product?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are utilized to support the Main Clutch (one needed).

Regularly bought with the product that you are currently checking out.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Front driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

Below is an additional product that praises the product being gone over.

Stub Axle Housing (2)

These are the axle housings (or center providers) utilized on the: Rad 2, Hawk 2,
Eagle, Blue Eagle LS II and Nitro Rustler. The housings are formed of
black nylon.

Includes: 2 axle housings

pcd 01/23/94

Below is a wonderful product that many others have purchased the exact same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

The below product also sets really well with the product being gone over.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas vehicles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum building

CONSISTS OF:
2 hex centers
4 axle pins

NEEDS:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

COMMENTS:
These centers could be utilized with other vehicles making use of the very same
    pin/hex design. These centers Will Not work on the T-Maxx or E-Maxx.

This product is frequently bought with the above stated product.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
2 rear 49mm (82mm center to center) turnbuckles

NEEDS:
Setup on the automobile

This product is frequently bought with the above stated product.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
2 front 39mm (69mm center to center) turnbuckles and direction
    sheet

NEEDS:
Setup on the automobile