Traxxas Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon building
Replaces a used or broken bellcrank set
May likewise be installed on the Traxxas Rustler, Outlaw and 2WD Slash
    models (assembled in different setups depending on model)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Machine Screws
2 Hollow Balls
4 Bushings
Instruction Sheet

REQUIRES:
Assembly and setup following the model handbook and included
guideline sheet

Right here is a fantastic product that many others have bought at the very same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This product is regularly acquired with the above pointed out product.

Extended Fr/Re Body Mounts Slash 2WD

This is the optional Pro-Line Extended Body Mount Set for the
1/10 scale Traxxas Slash 2WD Short Course Trucks.

FEATURES:
Adjustable front and rear body installs allow a variety of bodies
    to be used including rally vehicle bodies
Constructed of nylon, black in color
Screw-on body install system eliminates metal clips

CONSISTS OF:
Front and Rear Body Mounts and Publishes with Mounting Hardware

The below product additionally sets actually well with the product being reviewed.



The SW0231MG is a budget friendly waterproof digital servo with terrific torque for lots of applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It integrates leading edge technology with extremely high 12-bit (4096) resolution and metal equipments for your higher accuracy when evading puddles. This is a great upgrade if your wanting to drive your RC vehicle in any condition...rain, sleet, or snow.

Functions:

• Combines cutting edge
  technology with extremely high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Extremely strong metal equipments ensure long-life and durability.
• Our servos are totally green ? from products to production, these servos are environmentally friendly.
• Ideal for RC automobiles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Gear: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Score: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This product is regularly acquired with the above pointed out product.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Set for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Lowers the chassis 1" (25.4mm) for much better handling and higher
    cornering speed
Holds battery and electronic devices as deep in chassis as possible
45% lower battery position

CONSISTS OF:
Chassis
Lower Chassis
2 Nerf Bars
Battery Hold Down with Front and Rear Retainers
2 Front Shock Springs
Hardware and Directions

This product is regularly acquired with the above pointed out product.

Nerf Bars, For Traxxas Lcg Slash 2Wd, Blue

These are the optional RPM Nerf Bars in Blue for the 2WD Traxxas LCG Slash.

FEATURES:
Engineering grade nylon building
Replaces the Traxxas #5833, #5833A & #5833G nerf bars
Created specifically for the low center of mass (LCG) Slash
    chassis
Additional cross bracing to optimize rigidness while absorbing impact
    energy

CONSISTS OF:
Left and Right Nerf Bars in Blue