Traxxas Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon building and construction
Replaces a used or damaged bellcrank set
May likewise be installed on the Traxxas Rustler, Bandit and 2WD Slash
    models (put together in various setups depending upon model)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
Two Servo Arms
Two Shoulder Screws
Two 3x15 Counter Sunk Machine Screws
Two Hollow Balls
Four Bushings
Guideline Sheet

REQUIRES:
Assembly and setup following the model manual and consisted of
direction sheet

Right here is a wonderful item that many others have actually bought at the same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item is regularly gotten with the above discussed item.

Extended Fr/Re Body Mounts Slash 2WD

This is the optional Pro-Line Extended Body Mount Set for the
1/10 scale Traxxas Slash 2WD Short Course Trucks.

FEATURES:
Adjustable front and rear body installs permit a wide range of bodies
    to be utilized including rally car bodies
Constructed of nylon, black in color
Screw-on body mount system eliminates metal clips

CONSISTS OF:
Front and Rear Body Mounts and Publishes with Installing Hardware

The below item likewise pairs actually well with the item being gone over.

Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a budget plan friendly waterproof digital servo with fantastic torque for lots of applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It combines leading edge innovation with super high 12-bit (4096) resolution and metal equipments for your greater precision when dodging puddles. This is a great upgrade if your wanting to drive your RC automobile in any condition...rain, sleet, or snow.

Features:

• Combines leading edge
  innovation with super high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Exceptionally strong metal equipments make sure long-life and durability.
• Our servos are absolutely green ? from materials to production, these servos are ecologically friendly.
• Ideal for RC automobiles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Score: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This item is regularly gotten with the above discussed item.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Set for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Lowers the chassis 1" (25.4mm) for much better handling and greater
    catching speed
Holds battery and electronic devices as deep in chassis as possible
45% lower battery position

CONSISTS OF:
Chassis
Lower Chassis
Two Nerf Bars
Battery Hold Down with Front and Rear Retainers
Two Front Shock Springs
Hardware and Guidelines

This item is regularly gotten with the above discussed item.

Nerf Bars, For Traxxas Lcg Slash 2Wd, Blue

These are the optional RPM Nerf Bars in Blue for the 2WD Traxxas LCG Slash.

FEATURES:
Engineering grade nylon building and construction
Replaces the Traxxas #5833, #5833A & #5833G nerf bars
Created specifically for the low center of gravity (LCG) Slash
    chassis
Additional cross bracing to optimize rigidness while soaking up effect
    energy

CONSISTS OF:
Left and Right Nerf Bars in Blue