Traxxas Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FEATURES:
Composite nylon building
Replaces a used or damaged bellcrank set
May likewise be installed on the Traxxas Rustler, Bandit and 2WD Slash
    models (assembled in various setups depending on design)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
Two Servo Arms
Two Shoulder Screws
Two 3x15 Counter Sunk Device Screws
Two Hollow Balls
Four Bushings
Guideline Sheet

NEEDS:
Assembly and setup following the design handbook and included
instruction sheet

Here is a fantastic item that several others have actually bought at the exact same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item is regularly purchased with the above pointed out item.

Extended Fr/Re Body Mounts Slash 2WD

This is the optional Pro-Line Extended Body Mount Set for the
1/10 scale Traxxas Slash 2WD Short Course Trucks.

FEATURES:
Adjustable front and rear body mounts allow a wide array of bodies
    to be used including rally vehicle bodies
Constructed of nylon, black in color
Screw-on body install system eliminates metal clips

CONSISTS OF:
Front and Rear Body Mounts and Posts with Mounting Hardware

The listed below item additionally sets really well with the item being discussed.



The SW0231MG is a budget friendly waterproof digital servo with great torque for many applications. This brushed servo functions a speed of .17 and 208.0 oz-in of torque 6.0V. It combines leading edge innovation with extremely high 12-bit (4096) resolution and metal gears for your greater precision when dodging puddles. This is a great upgrade if your aiming to drive your RC automobile in any condition...rain, sleet, or snow.

Features:

• Integrates leading edge
  innovation with extremely high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Exceptionally strong metal gears ensure long-life and durability.
• Our servos are completely green ? from materials to production, these servos are environmentally friendly.
• Ideal for RC vehicles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Rating: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This item is regularly purchased with the above pointed out item.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Set for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Lowers the chassis 1" (25.4mm) for much better handling and greater
    catching speed
Holds battery and electronic devices as deep in chassis as possible
45% lower battery position

CONSISTS OF:
Chassis
Lower Chassis
Two Nerf Bars
Battery Hold Down with Front and Rear Retainers
Two Front Shock Springs
Hardware and Instructions

This item is regularly purchased with the above pointed out item.

Nerf Bars, For Traxxas Lcg Slash 2Wd, Blue

These are the optional RPM Nerf Bars in Blue for the 2WD Traxxas LCG Slash.

FEATURES:
Engineering grade nylon building
Replaces the Traxxas #5833, #5833A & #5833G nerf bars
Designed specifically for the low center of gravity (LCG) Slash
    chassis
Extra cross bracing to optimize rigidity while taking in impact
    energy

CONSISTS OF:
Left and Right Nerf Bars in Blue