Traxxas Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits a number of Traxxas
automobiles. .
Suches as: 1 gear only

Frequently purchased with the item that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is an additional item that praises the item being talked about.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Installation on automobile

The listed below item also pairs really well with the item being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item praises the main item below.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

This item is often purchased with the above mentioned item.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the automobile

REMARKS:
For main differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

You will like this item if you have the item earlier stated.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL version of both the Stampede
and Rustler.

Lots of others have actually purchased this item in addition to the item that you are presently reviewing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

Frequently purchased with the item that you are presently reviewing.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item is often purchased with the above mentioned item.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).