Traxxas Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive gear that fits a number of Traxxas
vehicles. .
Suches as: 1 gear only

Often acquired with the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Right here is another thing that praises the thing being talked about.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

REQUIRES:
Installation on car

The below thing likewise sets really well with the thing being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing praises the main item below.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

This thing is regularly acquired with the above discussed thing.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

INCLUDES:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Installation on the car

REMARKS:
For main differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

You will certainly like this thing if you have the thing earlier pointed out.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL version of both the Stampede
and Rustler.

Numerous others have actually acquired this thing along with the thing that you are presently reading about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Often acquired with the thing that you are presently reading about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This thing is regularly acquired with the above discussed thing.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for models with a slipper clutch.
Black plastic building

INCLUDES:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).